Abstract:Condenser is a huge,complex shell-and-tube heat exchanger.It is the key auxiliary equipment in power plants whose designs have a very important influence on thermal efficiency of electric power generation.At present,power plant condensers are traditionally designed based on recommendations from previous designs and experimental results,often based on the standards developed by the Heat Exchange Institute.However,it does not take a number of factors into account,including the tube arrangement.Hence,to study the tube arrangement effect on condenser performance and to optimize/improve the condenser design are very important for energy saving.The condenser performances,such as the back pressure and venting rate,are strongly affected by the tube arrangement,and there are three irreversible processes for the fluid flow,heat transfer and mass diffusion in condenser.Borrowing from the entransy analysis method of heat transfer process,the momentum entransy analysis and mass entransy analysis were performed on the steam flow and air mass diffusion process in condenser.Adopting the porous media model the momentum entransy balance equation and the air mass entransy balance equation of the steam flow were deduced,then,the relation of momentum entransy loss of the steam flow and the distributed flow and heat transfer parameters in the condenser and the relation of air mass entransy increase of the steam flow and the distributed parameters of flow,heat transfer and air mass fraction were deduced.With the two relations the effects of tube arrangement on the back pressure and the venting rate are numerically investigated.The numerical analyses on four typical condensers indicate that larger momentum entransy loss relates to larger back pressure,and larger air mass entransy increase relates to less venting rate.Based on the numerical results of the four kinds of tube arrangements 330 MW condensers,the principles for tube layout in condenser are summarized.For examples,the reasonable design of the periphery of the tube bundle,i.e.,the tube bundle profile,can lead the steam more uniformly entering the tube bundle,then the back pressure can be decreased;the tube arrangement should be well designed to properly guide the steam flow so as to avoid vortex flows,and a air cooling region should be well designed to reduce the venting rate.Finally,the bionic double-tree-shaped tube bundle condenser is introduced and the performances of a 330 MW condenser with bionic double-tree-shaped tube bundle are numerically analyzed.The results indicate that the steam uniformly enters the tube bundle,the thermal parameters are mainly centripetally distributed from the tube bundle periphery to the venting channel;the well-designed auxiliary steam entering channels result in a reduction of average steam velocity,hence,a reduction of flow resistance;The non-condensed steam is deeply condensed in the gradually contracted air cooling region,which strongly reduces the venting rate.Compared with the existing four kinds of condensers,its flow and thermal performances are much better.The back pressure of the rebuilt #2 condenser of Laicheng Power Plant by using the bionic double-tree-shaped tube bundle is decreased 1.5 kPa.

EFFECT OF THE AIR VELOCITY ON THE HEAT TRANSFER CAPACITY OF CONDENSER

Numerical Simulation and Experimental Study of Capillary Tubes

Sensitivity analysis of velocity field influence on condensers' performance and parallel circuit design based on actual air velocity distribution

Simulation, Experimentation, and Collaborative Analysis of Adjacent Heat Exchange Modules in a Vehicular Cooling System

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Numerical Simulation on Heat and Mass Transfer of Plate Evaporative Condenser

Analysis of Condenser Venting Rates Based on the Air Mass Entransy Increases

Heat transfer characteristics in vertical tube condensers: Experimental investigation and numerical validation

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Research on fluid flow and heat transfer characteristics in a three-dimensional condenser

Effect of Cooling Water Flow Path on the Flow and Heat Transfer in a 660 MW Power Plant Condenser

Effect of non-uniform air velocity distribution on evaporator performance and its improvement on a residential air conditioner

The enhancement effects of internal convection on the heat transport of condensing droplets out of pure steam and moist air

Numerical simulation of condensation heat transfer characteristics of R134a at high vapor velocity under different angles

Entransy Analysis of Tube Arrangement Effect on Condenser Performances and Its Application

Numerical Investigation of Air-Steam Condensation in a Vertically Enhanced Tube with Concave and Convex Surfaces

Modeling and experimental study of air-cooled finned-tube condenser using coupled distribution parameter method and air-side temperature distribution

The Study of Effects of Fin Parameters on Thermal Hydraulic Performance of a Vehicular Charged Air Cooler

Condensation in Horizontal Smooth Tubes: A New Heat Transfer Model for Heat Exchanger Design

Effects of tube shape on the distribution of film thickness and heat transfer performance in falling film evaporation

Numerical study on the thermal-hydraulic characteristic of an automotive parallel-flow condenser under non-uniform airflow