Abstract:In this work, resin‐derived carbon coating was prepared on carbon fibers by polymer impregnation pyrolysis method, then silicoboron carbonitride powder was prepared by mechanical alloying, and finally carbon fiber‐reinforced silicoboron carbonitride composites were prepared by hot‐pressing process. The effects of sintering densification and fiber coating on microstructure, mechanical properties, thermal shock resistance, and failure mechanisms of the composites were studied. Fiber bridging hinders the sintering densification, causing more defects in fiber‐dense area and lower strength. However, higher sintering temperature (1800–2000°C) can improve mechanical properties significantly, including bending strength, vickers hardness, and elastic module, because further sintering densification enhances matrix strength and fiber/matrix bonding strength, while the change of fracture toughness is not obvious (2.24–2.38 MPa·m1/2) due to counteraction of higher debonding resistance and less pull‐out length. However, fiber coating improves fracture toughness greatly via protecting carbon fibers from chemical corrosion and damage of thermal stress and external stress. Due to lower coefficient of thermal expansion, lower fiber loading ratio, less stress concentration at the fiber/matrix interface, and better defect healing effect, lower sintering temperature favors thermal shock resistance of composites, and thermal shock recession mechanisms are the damage of interface.

Preparation and mechanical performance of ductile Csf/Al2O3-BN composites-Part 2: Effects of fiber contents and ablation properties

Preparation and mechanical performance of ductile Csf/Al2O3-BN composites, Part 1: Effects of fiber length and sintering temperature

Ablation Behavior and Mechanism of Sicf/C-F/Sibcn Ceramic Composites with Improved Thermal Shock Resistance under Oxyacetylene Combustion Flow

Ablation and mechanical behaviour of C/C composites under an oxyacetylene flame and tensile loading environment

Ablation properties and mechanisms of BN-coated Cf-reinforced SiBCNZr ceramic composites under an oxyacetylene combustion torch

Preparation of Integrated Carbon Fiber Stitched Fabric Reinforced (sibcn) Ceramic/resin Double-Layered Composites for Ablation Resistance, Thermal Insulation and Compression Resistance Performance

Ablation Mechanism of AlSiB-C/C Composites under an Oxy-Acetylene Torch

Ablation behavior of Csf/SiC‐BN composites with polyborosilazane as sintering aids: High‐temperature damage mechanism

Effects of in Situ Amorphous Graphite Coating on Ablation Resistance of Sic Fiber Reinforced Sibcn Ceramics in an Oxyacetylene Flame

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

Preparation and flame ablation/oxidation behavior of ZrB2/SiC ultra-high temperature ceramic composites

Ablation behaviour of Csf/ZrB2-SiC composites fabricated by direct ink writing and reactive melt infiltration

Ablation behavior of Cf/ZrC-SiC and Cf/SiC composites produced by precursor infiltration and pyrolysis combined with gaseous silicon infiltration

Ablation Mechanism And Properties Of In-Situ Sialon Reinforced Bn-Sio2 Ceramic Composite Under An Oxyacetylene Torch Environment

Fracture Mechanical and Ablation Behaviors of C/SiC-Cu3Si-Cu Interpenetrating Composites and Their Dependence on Metal Addition and Interface Thickness

Ablation Behavior and Mechanism of Boron Nitride - Magnesium Aluminum Silicate Ceramic Composites in an Oxyacetylene Combustion Flame

Ablation resistance of ZrB2–SiC–AlN ceramic composites

Mechanical and thermal shock properties of C f /SiBCN composite: Effect of sintering densification and fiber coating

Long‐term oxidation and ablation behavior of Cf/ZrB2–SiC composites at 1500, 2000, and 2200°C

Long-term oxidation and ablation behavior of C<sub>f</sub>/ZrB<sub>2</sub>-SiC composites at 1500, 2000, and 2200C

Ablation behavior and mechanisms of 3D Cf/ZrB2-SiC composite applied in long-term temperature up to 2400 °C