Abstract:Ti6Al4V (TC4) alloy has been widely applied in the military, industrial, chemical, and medical fields due to their excellent thermal stability, corrosion resistance , and biocompatibility. However, titanium alloys are notorious for their poor tribological properties, such as their high friction coefficients and low surface bearing capacities. To tackle this problem, combination of laser surface texturing (LST) and double glow plasma chromizing was conducted to improve the wear resistance of TC4. LST was first conducted to produce uniform dimples with a diameter of 300 μm and gradient density of 11 % on the Ti6Al4V substrate. A chromizing coating (Cr-coating) was subsequently deposited on the surfaces of the textured and raw Ti6Al4V alloy by double glow plasma surface alloying (DGPSA). A continuous and compact Cr-coating with a thickness of about 55 μm was formed on TC4 after being maintained at a temperature of 850 °C, and the coating was mainly composed of a solid solution and intermetallic compounds of Cr 2 Ti phases. The surface hardness after alloying was two times higher than that of the TC4 substrate. Comparative assessments on the wear resistance of the Cr-coatings with and without LST treatment and the TC4 alloy were carried out using a ball-on-disk wear tester. The results showed that the mass loss and specific wear rate of the duplex-treated sample were 1.54 mg and 7.14 × 10 −4 mm 3 ·N −1 ·m −1 . The mass loss and specific wear rate of the TC4 were 4.32 mg and 1.62 × 10 −3 mm 3 ·N −1 ·m −1 . The specific wear rates of the four tested samples were in the following order: the duplex-treated TC4 < textured TC4 < chromized TC4 < polished TC4. The coating obtained by LST-double glow plasma chromizing duplex treatment exhibited an outstanding durability and the best mechanical performance. Thus, this approach be used for the protection of Ti6Al4V surface in engineering components and medical instruments.

Combining thermo-diffusing titanium and plasma nitriding to modify C61900 Cu–Al alloy

Modification mechanism of Ti-6Al-4V alloy with pre-coated Ti-Cu-Al multilayer film treated by ion nitriding: Experiments and first-principles calculations

High Temperature Plasma Nitriding to Modify Ti Coated C17200 Cu Surface: Microstructure and Tribological Properties

Multiple Needle Cathodes Plasma Surface Alloying of Ti6Al4V with W-Mo-C-N

Microstructural and Performance Analysis of (TiAl)95−xCu5Nix Coatings Prepared via Laser Surface Cladding on Ti–6Al–4V Substrates

A Novel Anti-Frictional Multiphase Layer Produced by Plasma Nitriding of PVD Titanium Coated ZL205A Aluminum Alloy

Characterisation and Oxidation Behaviour of Plasma Surface Alloyed on Γ-Tial Alloy

Properties of TiAlCrN coatings prepared by vacuum cathodic arc ion plating

Microstructure, Oxidation Behavior and Adhesion of a CoNiCrAlTaY Coating Deposited on a High Nb–TiAl Alloy by Plasma Surface Metallizing Technique

Fabrication and Characterization of In-Situ Duplex Plasma-Treated Nanocrystalline Ti/AlTiN Coatings

A novel approach to coating for improving the comprehensive high-temperature service performance of TiAl alloys

Synthesis, Structure, and Properties of the High Nb–TiAl Alloy after Ni Coatings by Plasma Surface Alloying Technique

Properties of Ti–Zr–Nb–Cu–Ni multi-principal-component alloy coatings prepared by laser cladding on a Ti–6Al–4V surface

Study of TiCuN/ZrN multilayer coatings with adjustable combination properties deposited on TiCu alloy

Improved Wear Resistance and Mechanical Properties of Al Matrix with TiAl-based Coatings

In-situ TiB2-TiC reinforced Fe-Al composite coating on 6061 aluminum alloy by laser surface modification

Enhancement of Wear and Corrosion Resistance of Ti6Al4V Alloy through Hollow Cathode Discharge-Assisted Plasma Nitriding

Combining laser surface texturing and double glow plasma surface chromizing to improve tribological performance of Ti6Al4V alloy

Enhanced Interfacial Bonding and Superior Oxidation Resistance of CoCrAlY-TiB2 Composite Coating Fabricated by Air Plasma Spraying

Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying

Tribological properties of self-healing NiCrAlY/Cr3C2-Ti3AlC2 coating at high temperatures