Abstract:Tensile deformation and fracture modes in peak-aged cast Mg-11Y-5Gd-2Zn-0.5Zr (wt pct) (WGZ1152) samples at temperatures between 298 K [25 °C, room temperature (RT)] and 623 K (350 °C) (0.33 to 0.69T m) were studied in situ inside a scanning electron microscope (SEM) using electron backscatter diffraction (EBSD) and slip trace analysis. The ultimate tensile strength (UTS) (265 MPa) and yield strength (YS) (193 MPa) at 523 K (250 °C) were 91 and 80 pct of those at RT, respectively. The observed dominant slip mode transitioned from basal 〈a〉 slip (100 pct) to basal 〈a〉 slip (81 pct) combined with prismatic 〈a〉 slip (12 pct) from RT to 473 K (200 °C). As the temperature increased to 623 K (350 °C), basal 〈a〉 slip (67 pct) and pyramidal 〈c+a〉 slip (25 pct) became the dominant slip modes. The estimated critical resolved shear stress (CRSS) ratio of pyramidal 〈c+a〉 slip/basal 〈a〉 slip (7.3) was lower than that of prismatic 〈a〉 slip/basal 〈a〉 slip (12.7) at temperatures above 573 K (300 °C). Prismatic 〈a〉 slip and pyramidal 〈c+a〉 slip were more active at higher strains for moderate temperatures [473 K to 523 K (200 °C to 250 °C)] and at high temperatures [573 K to 623 K (300 °C to 350 °C)], respectively. A transition in the dominant fracture mode occurred from transgranular cracking (40 pct) combined with intergranular cracking (60 pct) to intergranular cracking as temperatures increased from RT to 623 K (350 °C). The intergranular crack nucleation sites tended to be located at grain boundaries and the interface between the Mg matrix and the large intermetallic grain boundary X phase. Slip bands were associated with transgranular crack nucleation.

High‐Temperature Tensile and Compressive Behavior of Peak‐Aged Sand‐Cast Mg–10Gd–3Y–0.5Zr Alloy

The Elevated-Temperature Mechanical Behavior of Peak-Aged Mg–10Gd–3Y–0.4Zr Alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Age Hardening Characteristics and Mechanical Properties of Mg-3.5dy-4.0gd-3.1nd-0.4zr Alloy

High temperature mechanical properties of Sand-cast Mg-Gd-Y magnesium alloy

Effect of Heat Treatment on Microstructure, Mechanical Properties and Fracture Behaviors of Sand-Cast Mg-4Y-3Nd-1Gd-0.2Zn-0.5Zr Alloy

Effect of Heat Treatment on Tensile Properties, Impact Toughness and Plane Strain Fracture Toughness of Sand-Cast Mg-6Gd-3Y-0.5Zr Magnesium Alloy

Microstructure Characterization and High-Temperature Shear Strength of the Mg–10Gd–3Y–1.2Zn–0.5Zr Alloy in the As-Cast and Aged Conditions

Microstructure and Mechanical Properties of Mg–2.0Gd–1.2Y–1.0Zn–0.2Zr Alloy

Microstructure Evolution and Mechanical Properties of High Performance Mg–10Gd–2Y–0·5Zn–0·3Zr Alloy During Heat Treatments

Influence of Heat Treatment on Cyclic Deformation and Low-Cycle Fatigue Behavior of Sand-Cast Mg–10Gd–3Y–0.5Zr Magnesium Alloy

High temperature mechanical behavior of low-pressure sand-cast Mg–Gd–Y–Zr magnesium alloy

Effect of Gd content on high temperature mechanical properties of Mg–Gd–Y–Zr alloy

Research on Microstructure and Mechanical Properties of Mg-10Gd-3Y-2Nd-0.5Zr Alloy

Microstructure and Elevated-Temperature Tensile Properties of Differential Pressure Sand Cast Mg-4Y-3Nd-0.5Zr Alloy

Effect of heat treatment on mechanical properties and microstructure evolution of Mg-9.5Gd-4Y-2.2Zn-0.5Zr alloy

Effect of Heat Treatment on Microstructures and Mechanical Properties of Sand-Cast Mg-10Gd-3Y-0.5Zr Magnesium Alloy

Microstructure and strengthening mechanisms of a cast Mg–1.48Gd–1.13Y–0.16Zr (at.%) alloy

High Cycle Fatigue Behavior and Mechanical Performance of a Novel Sand-Cast Mg-Nd-Gd Alloy: Effect of Heat Treatment

In-Situ Study of the Tensile Deformation and Fracture Modes in Peak-Aged Cast Mg-11Y-5Gd-2Zn-0.5Zr (weight Percent)