Abstract:This study aims to investigate the impact of flow rotation and oxygen concentration on the synthesis of carbon nanomaterials using n-butanol diffusion flames in a rotating stagnation flow with a liquid pool and a catalytic Ni substrate. With increasing angular velocity (ω), the diffusion flame shifts slightly toward the upper oxidizer nozzle, experiences a lower strain rate, and becomes stronger with a higher maximum flame temperature at a fixed oxygen concentration (Ω O ). Meanwhile, the soot layer thickens and gradually turns yellowish. Field Emission Scanning Electron Microscopy (FESEM) analyses confirm that carbon nanotubes (CNTs) can only be fabricated at ω = 2 or 3 rps when Ω O = 21%, highlighting the critical role of flow rotation. Interestingly, the optimal positions for CNT synthesis consistently occur at the same sampling position (1.5 mm below the upper edge of the blue flame) for all values of oxygen concentration (Ω O ). The corresponding temperature ranges for Ω O = 19%, 18%, and 17% are approximately 950°C, 820–920°C, and 800–850°C, respectively, which align with existing literature. High-resolution transmission electron microscopy (HRTEM) images reveal both typical straight tubular and bamboo-like CNT structures. Raman spectra indicate superior graphitization at high angular velocities (ω). Notably, at ω = 0 rps, the intensity ratio of the D- and G-bands is greater than 1 (I D /I G >1); however, as ω increases, the opposite holds (I D /I G <1), with its value gradually decreasing. This suggests that the swirl effect enhances graphite layer crystallization. Importantly, the strain rate controlled by flow rotation significantly influences CNT fabrication, considering both residence time and carbon source. The key finding of this study is that swirl flow enhances both the quality and quantity of CNTs synthesized via n-butanol diffusion flames.

Numerical Assessment On Rotation Effect Of The Stagnation Surface On Nanoparticle Deposition In Flame Synthesis

Spray Swirling Flame Dynamic under Combined Modulation of Air and Fuel

Experimental investigation on carbon deposition characteristics of aeroengine swirl nozzle and its effect on spray behaviors

Nanoparticle Transport and Deposition in Boundary Layer of Stagnation-Point Premixed Flames

Numerical Simulation of Nanoparticle Synthesis in Diffusion Flame Reactor

Effect of Precursor Loading on Non-Spherical TiO2 Nanoparticle Synthesis in a Diffusion Flame Reactor

Effects of Atomization Injection on Nanoparticle Processing in Suspension Plasma Spray

Modelling and Optimization for Deposition of SiO X N Y Films by Radio-Frequency Reactive Sputtering

On the Response of Spherical Premixed Flames under Rotation

Direct Synthesis of Nanostructured Tio2 Films with Controlled Morphologies by Stagnation Swirl Flames

Numerical Analysis of Catalyst Particle Deposition Characteristics in a Flue Gas Turbine with an Improved Particle Motion and Deposition Model

The Effects of Rotation Rate on the Characteristics of Premixed Propane–air Swirling Tubular Flames

Numerical Analysis of Rotating Scans' Effect on Surface Roughness in Laser-Powder Bed Fusion

1-D and 2-D numerical simulation of catalytic combustion at stagnation point

Time-Dependent Stagnation Point Flow of Water Conveying Titanium Dioxide Nanoparticle Aggregation on Rotating Sphere Object Experiencing Thermophoresis Particle Deposition Effects

Rotation Induced by Non-Uniform Gas–solid Phase Reactions of a Non-Spherical Particle

The Effect of Intrinsic Instability on the Surface Topography of Spherical 2-Acetylfuran Flame

Deposition Behavior of Semi-Molten Spray Particles During Flame Spraying of Porous Metal Alloy

Numerical investigation of particle size distribution, particle transport and deposition in a modified chemical vapor deposition process

In-Situ Flame-Synthesized Carbon Nanomaterials via an Impinging Swirl Flow with an N-Butanol Pool

Rarefied flow effects on stabilization and extinction of rotating-disk flame at low pressures