Abstract:Inorganic perovskite materials have gained considerable attention owing to their good thermal stability, high absorption coefficient, adjustable bandgap, and simple preparation. However, most inorganic perovskites are sensitive to water and need to be prepared under inert environments in a glove box, which increases their preparation cost. In this study, we used a simple one-step spin coating anti-solvent process to prepare CsPbI2Br, which was then annealed in humid air (relative humidity < 35%) at 300 degrees C for 5 min with isopropanol as the anti-solvent. An inorganic perovskite solar cell with fluorine-doped tin dioxide/compact TiO2/mesoporous TiO2/CsPbI2Br/hole transport materials/Ag structure was prepared. By varying the concentration of the mesoporous precursor, we controlled the thickness of mesoporous TiO2 in order to investigate its effect on the properties of the perovskite films and devices. The X-ray diffraction (XRD) results confirmed the successful synthesis of CsPbI2Br in humid air. Moreover, the thickness of the substrate affected the crystal growth orientation. The scanning electron microscopy results revealed that the thickness of the mesoporous titanium dioxide substrate affected the crystallization processing of CsPbI2Br, resulting in the formation of compounds with different morphologies and phases. The ultraviolet-visible (UV-Vis) and photoluminescence spectra of the perovskite materials revealed that the substrate thickness affected their optical properties. With a decrease in the thickness of the mesoporous TiO2 substrate, the bandgap of CsPbI2Br increased slightly. At the substrate thickness of 145 nm, the defect density of state of CsPbI2Br increased. At the optimum mesoporous titanium dioxide substrate thickness of 732 nm, the device showed the best power conversion efficiency of 8.16%. The electrochemical impedance spectroscopy measurements revealed that the devices prepared on thicker mesoporous layers showed better carrier extraction and transmission capabilities but higher interfacial charge recombination resistance, leading to a lower open-circuit voltage but higher current density. Thus, an increase in the thickness of the mesoporous substrate improved the photovoltaic performance of the devices. The stability of the CsPbI2Br perovskite film improved with an increase in the mesoporous substrate thickness. The stability test results along with the UV-Vis and XRD analysis results showed that the perovskite film prepared on the 732 nm-thick substrate showed no significant structure change after being placed in humid air for 144 h. The stability of the perovskite solar cells was also investigated. The device with the 732 nm-thick substrate could maintain its original efficiency of 73% after exposure to air with relative humidity less than 35% for 72 h. Thus, inorganic perovskite solar cells could be successfully prepared in the humid air environment.

Fabrication of Highly Luminescent Quasi Two-Dimensional CsPbBr 3 Perovskite Films in High Humidity Air for Light-Emitting Diodes

Efficient Flexible Inorganic Perovskite Light-Emitting Diodes Fabricated with CsPbBr3 Emitters Prepared Via Low-Temperature in Situ Dynamic Thermal Crystallization

Solution-processed Highly Bright and Durable Cesium Lead Halide Perovskite Light-Emitting Diodes.

High-performance quasi-2D perovskite solar cells with power conversion efficiency over 20% fabricated in humidity-controlled ambient air

Fabrication of highly transparent CsPbBr3 quantum-dot thin film via bath coating for light emission applications

Phosphonic Chloride Assisted Fabrication of Highly Emissive Mixed Halide Perovskite Films in Ambient Air for Blue Light-Emitting Diodes

Highly Emissive Green Metal Halide Perovskite Solids: Formation Kinetics, Enhanced Heat, Light, and Polar Solvent Resistance, and Light-Emitting Application

Highly Stable and Photoluminescent CsPbBr3/Cs4PbBr6 Composites for White-Light-Emitting Diodes and Visible Light Communication

Improving Crystallization and Photoelectric Performance of CsPbI2Br Perovskite under Ambient Air Via Dynamic Hot-Air Assisted Recrystallization Strategy

Hole Transport Layer Free Perovskite Light-Emitting Diodes with High-Brightness and Air-Stability Based on Solution-Processed CsPbBr3-Cs4PbBr6 Composites Films

Highly Luminescent and Stable Perovskite Quantum Dots Films for Light‐Emitting Devices and Information Encryption

Cs4PbBr6/CsPbBr3 Perovskite Composites with Near-Unity Luminescence Quantum Yield: Large-Scale Synthesis, Luminescence and Formation Mechanism, and White Light-Emitting Diode Application.

Scalable All‐Evaporation Fabrication of Efficient Light‐Emitting Diodes with Hybrid 2D–3D Perovskite Nanostructures

High‐Throughput Combinatorial Optimizations of Perovskite Light‐Emitting Diodes Based on All‐Vacuum Deposition

Fabrication of Stable CsPbI2Br Perovskite Solar Cells in the Humid Air

Quantum dot-modified CsPbIBr2 perovskite absorber for efficient and stable photovoltaics

Efficient CsPbBr 3 Perovskite Light-Emitting Diodes via Novel Multi-Step Ligand Exchange Strategy Based on Zwitterionic Molecules

Reducing Nonradiative Losses of Air‐Processed Perovskite Films via Interface Modification for Bright and Efficient Light Emitting Diodes

Giant efficiency and color purity enhancement in multicolor inorganic perovskite light-emitting diodes via heating-assisted vacuum deposition

Rapid Crystallization of All-Inorganic CsPbBr3 Perovskite for High-Brightness Light-Emitting Diodes

Water assisted chlorination enables ambient air fabrication of mixed halide perovskite films for blue light emitting diodes