Abstract:Organic solar cells(OSCs) are a promising cost-effective alternative for utility of solar energy, and possess advantages such as low cost, light weight and flexibility. Much attention has been focused on the development of OSCs(synthesis of new donor or acceptor materials, control of morphology of active layer and fabrication of new device structures) which have seen a dramatic rise in efficiency over the last decade. Since the bulk heterojunction concept was reported in 1995, two-component(binary) blend has been predominant as active layer and achieved great success with power conversion efficiencies(PCEs) up to ca. 10%. Ternary blend of active layer consisting of a donor material, an acceptor material and a third component has received increasing attention in recent five years. The third components include light-absorbing polymers or small molecules, fullerene or non-fullerene acceptors, inorganic nanomaterials(quantum dots, metal nanomaterials or carbon-based nanomaterials) and organic nonvolatile additives(polymers or small molecules). Compared with binary blend, ternary blend may present some advantages: broader and stronger absorption; more efficient charge transfer and charge transport, better morphology and improved stability. In this work, we fabricated ternary blend OSCs based on P3HT/TT-TTPA/PC61 BM blend. TT-TTPA is a conjugated small molecule with thiazolothiazole as acceptor unit, triphenylamine as donor unit and thiophene as bridge. TT-TTPA has good miscibility with PC61 BM and the phase separation scale of TT-TTPA/PC61 BM blend is very small. During solvent annealing and thermal annealing, the small amount of TT-TTPA in P3 HT domains can move from P3 HT domains to PC61 BM domains, thus increase the phase purity of P3 HT domains that can undergo crystallization. After optimization of the weight ratio of TT-TTPA in ternary blend, we achieved better PCE(4.41%) relative to binary blend(3.85%). Effects of TT-TTPA on absorption, crystallinity and morphology of P3HT:PC61BM blend films were investigated by UV-vis, X-ray diffraction and atomic force microscopy.

Composition and Processing Dependent Miscibility of P3HT and PCBM in Organic Solar Cells by Coarse-Grained Molecular Simulations

[6,6]-Phenyl-c61-butyric Acid 2-((2-(dimethylamino)ethyl)(methyl)amino)-ethyl Ester As an Acceptor and Cathode Interfacial Material in Polymer Solar Cells

Rationally Tuning Blend Miscibility of Polymer Donor and Nonfullerene Acceptor for Constructing Efficient Organic Solar Cells<sup>※</sup>

Characterizing the Morphology and Efficiency of Organic Solar Cells by Multiscale Simulations

Miscibility Control by Tuning Electrostatic Interactions in Bulk Heterojunction for Efficient Organic Solar Cells

2D/1a Strategy to Regulate Film Morphology for Efficient and Stable Nonfullerene Organic Solar Cells

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

Ternary Blend Organic Solar Cells Based on P3HT/TT-TTPA/PC_(61)BM

Dynamics of the sub-ambient gelation and shearing of solutions of P3HT incorporated with a non-fullerene acceptor o-IDTBR towards active layer formation in bulk heterojunction organic solar cells

Suppression of Thermally Induced Fullerene Aggregation in Polyfullerene-Based Multiacceptor Organic Solar Cells

Favorable Mixing Thermodynamics in Ternary Polymer Blends for Realizing High Efficiency Plastic Solar Cells

P3ht: Pcbm Solar Cells-The Choice Of Source Material

Tuning the Morphology of Solution-Sheared P3ht:Pcbm Films

Review on performance analysis of P3HT:PCBM-based bulk heterojunction organic solar cells

Reduced miscibility between highly compatible non-fullerene acceptor and donor enables efficient ternary organic solar cells

Mutual Diffusion of Model Acceptor/Donor Bilayers under Solvent Vapor Annealing as a Novel Route for Organic Solar Cell Fabrication

Modulation of Phase Separation Morphology by Configuration Engineering in Bulk Heterojunction Organic Solar Cells

Modulation of Morphological, Mechanical, and Photovoltaic Properties of Ternary Organic Photovoltaic Blends for Optimum Operation

Influence of Polymer Aggregation and Liquid Immiscibility on Morphology Tuning by Varying Composition in PffBT4T-2DT/Non-Fullerene Organic Solar Cells

Numerical studies of P3HT : PCBM organic solar cell with an additional polymer layer using drift diffusion model

Miscibility Regulation and Thermal Annealing Induced Hierarchical Morphology Enables High‐Efficiency All‐Small‐Molecule Organic Solar Cells Over 17%