Abstract:As an important component of the air-breathing combined precooling cycle engine of the hypersonic aircraft, the compact heat exchanger plays an important role in precooling the incoming air. However, the compact heat exchanger is easy to frosting during the precooling operation, which leads to an extremely unfavorable result, that is, the specific impulse and specific thrust of the engine significantly decrease. Therefore, in order to maintain the performance of the engine, some measures should be taken to defrosting the compact heat exchanger of the engine. In order to carried out the frosting and defrosting experiments on the compact heat exchanger that operating at relatively low altitudes, the frosting and defrosting performance of the compact heat exchanger are experimentally studied in the wind tunnel under the conditions of moderate airflow humidity value (6.4 g/kg), as well as the flow velocity and the temperature of the mainstream are 10 m/s and 50 °C, respectively. In the defrosting experiments, anhydrous methanol and anhydrous ethanol are sprayed into the mainstream as the defrosting solvents, respectively, and the mass ratios of anhydrous methanol to water and anhydrous ethanol to water are 0.75, 1.0 and 1.25. The experimental results indicate that for the frosting experiment, after coolant flows through the inside of the heat exchanger tube bundles, the frost layer quickly condenses on the outside of tube bundles. However, in the defrosting experiments, once a certain mass ratio of anhydrous methanol or anhydrous ethanol is sprayed into the main flow, the wall temperature of the heat exchanger tube bundles increases significantly, and the wall temperature is close to or higher than the freezing point of water. Furthermore, the defrosting effect and the heat transfer rate are obviously improved, and the pressure loss coefficient drops sharply. Through the analyzation of the defrosting experimental results, it is found that the defrosting performance of anhydrous methanol and anhydrous ethanol are obvious different, and the defrosting effect of anhydrous methanol is significantly higher than that of anhydrous ethanol with the same mass ratio. Within the range of experimental study parameters, for anhydrous methanol, the best defrosting performance can be obtained when the mass ratio is 1.0; and for anhydrous ethanol, the best defrosting effect can be realized when the mass ratio is 1.25. However, the defrosting performance of anhydrous ethanol with the mass ratio of 1.25 is still slightly lower than that of anhydrous methanol with the mass ratio of 0.75. Moreover, in order to achieve the best defrosting performance of the compact heat exchanger, the optimal mass ratio of anhydrous methanol to water may be in the range of between 1.0 and 1.25; and the optimal mass ratio of anhydrous ethanol to water should be greater than 1.25.

Effects of Surface Wettability and Defrosting Conditions on Defrosting Performance of Fin-Tube Heat Exchanger

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Temperature-gradient-enabled Prohibition of Condensation Frosting on Fin Surfaces

Performance of the frosting characteristics of fin-and-tube heat exchanger subject to superhydrophobic coating

Optimization of fin surface wettability for promoting the dust removal in heat exchangers under frosting-defrosting conditions

Effect of surface coating on defrosting water drainage characteristics of vertical-fin microchannel frosting evaporator

Frosting Behavior of Louvered-Fin and Tube Heat Exchanger after Surface Treatment: Experimental Analysis

Enhancing heat-exchanger performance in frost conditions via superhydrophobic surface modification

Experimental Investigation of the Performance of Microchannel Heat Exchangers with a New Type of Fin under Wet and Frosting Conditions

Experimental investigation of frost and defrost performance of microchannel heat exchangers for heat pump systems

Experimental Study of Cyclic Frosting and Defrosting on Microchannel Heat Exchangers with Different Coatings

Effect of Surface Wettability on Frosting,defrosting and Drainage

Feasibility study of a defrosting method at thin frost moment based on temperature difference recognition

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Efficient Defrosting on Hybrid Surfaces with Heterogeneous Wettability

Experimental Study of Frost Formation on Cold Surfaces with Various Fin Layouts

Experimental studies on the frosting and defrosting performance of compact heat exchanger under moderate humidity condition

An Experimental Study on the Effects of Frosting Conditions on Frost Distribution and Growth on Finned Tube Heat Exchangers

Review of restraint frost method on cold surface

Effect of Fin Types of Outdoor Fan-Supplied Finned-Tube Heat Exchanger on Periodic Frosting and Defrosting Performance of a Residential Air-Source Heat Pump

Study on Frost-Suppression Characteristics of Superhydrophobic Aluminum Surface Heat Exchanger Applied in Air Source Heat Pump