Abstract:Metal supported solid oxide fuel cells (MS-SOFC) possess several advantages like good mechanical property, easy assembling, fast start-up and capability to maintain redox stable due to fuel leakage. However, it has been a critical challenge to deposit cathode on the metal supported cell in the oxidizing atmosphere, which is mainly limited by the low calcination temperature yielding vulnerable electrolyte-electrode interface. The cathodes prepared in the protecting atmosphere are also not satisfied, instead it will increase the complexity of the cell fabrication process. Lower down the cathode deposition temperature using aqueous infiltration has become one of the optimized methods for MS-SOFC. Also, we have proposed an alternative way for the fabrication of metal supported single cell with robust cathode through whole cell reduction. Here, we present results of both above two approaches for the fabrication of nano-structured cathodes in MS-SOFC. The cells in this study are based on Fe-Ni (1:1 in mol ratio) support, Fe-Ni/YSZ anode and YSZ electrolyte prepared through tape-casting, thermal isostatic pressing and co-firing. As illustrated in the following schematic configuration, La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF) cathodes were deposited in the porous YSZ layer of the pre-reduced Ni-Fe|Ni-Fe-YSZ||YSZ||P-YSZ substrate by infiltration and fired at the cell operation temperature around 700 oC. A-site deficiency of ~4-8% was introduced into LSCF cathode and was expected to enhance the sintering activity of LSCF nano particles at low calcination temperature and to enhance the cathode performance by the excess cobalt and iron oxide at LSCF surface. As in the second approach, Sr0.95Ti0.3Fe0.63Ni0.07O3-δ – Gd0.1Ce0.9O1.95 (STFNi-GDC) graded cathode will be screen printed on the NiO-Fe2O3|NiO-Fe2O3-YSZ||YSZ|GDC substrate and fired at high temperature in air as normal cathode preparation procedure. Then the whole cell will be reduced in H2-Ar to obtain Fe-Ni alloy support and reduced STFNi cathode with in-situ exsolved (Fe,Ni) alloy nano particles anchored in the oxide surface. During the cell test, the reduced STFNi-(Fe,Ni) will be re-oxidized in air, forming the surface decorated iron and cobalt oxide particles, which were presumably to be expected to increase the cathode performance through improvement of oxygen surface exchange coefficient. Figure 1

Fabrication of 3D Ni Nanosheet Array on Crofer22APU Interconnect and NiO-YSZ Anode Support to Sinter with Small-Size Ag Nanoparticles for Low-Temperature Sealing SOFCs

Joining of Solid Oxide Fuel/electrolysis Cells at Low Temperature: A Novel Method to Obtain High Strength Seals Already at 300 °C

A Low-Temperature Sealing Method for Metal-Supported Oxide Fuel Cell Applications: Ni–Sn Transient Liquid Phase Bonding

Fabrication of Metal-Supported Tubular Solid Oxide Fuel Cell by Phase-Inversion Method and in Situ Reduction

Novel Co-precipitation method to synthesize NiO-YSZ nanocomposite powder for solid oxide fuel cell

Fabrication of composite cathode by a new process for anode-supported tubular solid oxide fuel cells

Fabrication of Dense La0.7Ca0.3Cr0.97O3-delta Interconnect Thin Membrane on Composite Anode Support by Co-firing

Effective Ag–CuO Sealant for Planar Solid Oxide Fuel Cells

An Efficient Construction of Nano-Interfaces for Excellent Coking Tolerance of Cermet Anodes

Effects of Adding Alumina to the Nickel-Zirconia Anode Materials for Solid Oxide Fuel Cells and a Two-Step Sintering Method for Half-Cells

A Phase Inversion/Sintering Process to Fabricate Nickel/Yttria-Stabilized Zirconia Hollow Fibers As the Anode Support for Micro-Tubular Solid Oxide Fuel Cells

A Novel High Performance Composite Anode with in Situ Growth of Fe-Ni Alloy Nanoparticles for Intermediate Solid Oxide Fuel Cells

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

In-Situ Formation of Nano-Structured Cathode on Metal Supported SOFC

Investigation on Silver Electric Adhesive Doped with Al2o3 Ceramic Particles for Sealing Planar Solid Oxide Fuel Cell

Fabrication and Interfacial Structure of Ni-YSZ-LSM Porous Scaffold for Solid Oxide Fuel Cells

Fabrication of Dense La0.7Ca0.3Cr0.97O3-δ Interconnect Thin Membrane on Composite Anode Support by Co-firing

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Effect of Composite Pore-Former on the Fabrication and Performance of Anode-Supported Membranes for SOFCs

Fabrication of Nickel-YSZ Cermet Nanofibers Via Electrospinning

Fabrication of Anode Supported Micro Tubular SOFCS by Dip-Coating Process on NiO/YSZ Hollow Fibers