Abstract:Electrochemical machining (ECM) has become more prevalent in titanium alloy processing. However, the presence of the passivation layer on the titanium alloys significantly impacts the performance of ECM. In an attempt to overcome the passivation effects, a high-temperature electrolyte or the addition of halogen ions to the electrolyte has been used. Still, it often results in compromised machining accuracy and surface roughness. This study applied laser and shaped tube electrolytic machining (Laser-STEM) for titanium alloy drilling, where the laser was guided to the machining zone via total internal reflection. The performance of Laser-STEM using different types of electrolytes was compared. Further, the effects of laser power and pulse voltage on the machining side gap, material removal rate (MRR), and surface roughness were experimentally studied while drilling small holes in titanium alloy. The results indicated that the use of passivating electrolytes improved the machining precision, while the MRR decreased with an increase in laser power during Laser-STEM. The MRR showed an increase while using aggressive electrolytes; however, at the same time, the machining precision deteriorated with the increase in laser power. Particularly, the maximum feeding rate of 6.0 mm/min for the tool electrode was achieved using NaCl solution as the electrolyte during Laser-STEM, marking a 100% increase compared to the rate without the use of a laser. Moreover, the model and equivalent circuits were also established to illustrate the material removal mechanisms of Laser-STEM in different electrolytes. Lastly, the processing of deep small holes with a diameter of 1.5 mm, a depth of 38 mm, and a surface roughness of Ra 2 µm was achieved via Laser-STEM without the presence of a recast layer and heat-affected zones. In addition, the cross-inner flow channels in the titanium alloys were effectively processed.

Electrochemical Micromachining on Titanium Using the NaCl-containing Ethylene Glycol Electrolyte

Jet Electrochemical Micromilling of Ti-6Al-4V Using NaCl–Ethylene Glycol Electrolyte

Electrolyte Jet Machining of Ti1023 Titanium Alloy Using NaCl Ethylene Glycol-Based Electrolyte

Study on the Effect of Electrolytes on Processing Efficiency and Accuracy of Titanium Alloy Utilizing Laser and Shaped Tube Electrochemical Machining

Titanium Alloy Ti-6Al-4V Electrochemical Dissolution Behavior in NaNO3 and NaCl Solutions at Low Current Density

Electrochemical Properties and Jet Electrochemical Micromilling of (TiB+TiC)/Ti6Al4V Composites in NaCl+NaNO3 Mixed Electrolyte

Effect of Anodic Behavior on Electrochemical Machining of TB6 Titanium Alloy

Electrochemical machining of titanium alloy blades using optimized cathode with built-in insulators

Electrochemical Micromachining of NiTi Shape Memory Alloy with Ethylene Glycol–nacl Electrolyte Containing Ethanol

Simultaneous gas electrical discharge and electrochemical jet micromachining of titanium alloy in high-conductivity salt solution

Jet Electrochemical Machining of TB6 Titanium Alloy

Electrochemical Polishing Method for Titanium Alloys with a Microgroove Structure

Processing of titanium alloys with improved efficiency and accuracy by laser and electrochemical machining

Electrochemical micro-machining of high aspect ratio micro-tools with a reverse conical shape tip using electrolyte liquid membrane

An Investigation of the Efficient–Precise Continuous Electrochemical Grinding Process of Ti–6Al–4V

Study on electrochemical polishing mechanism of TC4 titanium alloy

Investigation on Parametric Effects on Groove Profile Generated on Ti1023 Titanium Alloy by Jet Electrochemical Machining

Two-level electrochemical micromachining of titanium for device fabrication

A study on ultrasonic-assisted micro-EDM of titanium alloy

Selection and Optimization of Electrolyte for Micro Electrochemical Machining on Stainless Steel 304

Surface morphology and electrochemical behaviour of Ti-48Al-2Cr-2Nb alloy in low-concentration salt solution