Abstract:<p>Thermoplastic vulcanizate (TPV) have been widely used in industry, and injection molding is one of the most widely used technique to produce TPV products. In this study, effects of shear during injection molding on the anisotropic microstructure and properties of EPDM/PP TPV containing rubber nanoparticle agglomerates was systematically studied by using quantitative nanomechanical mapping of atomic force microscopy (AFM-QNM) for the first time. The shear of injection molding induced break-up of the EPDM nanoparticles agglomerates, and a significant decrease in the size of the latter with increasing shear rate was observed. Meanwhile, the shear orients both PP crystals and EPDM nanoparticle agglomerates, and their orientation degree along the shear direction, and the crystallinity of PP increase with increasing the shear rate. As a result, whatever the anisotropy, the Young's moduli at nanoscale of PP obtained by AFM-QNM, and the tensile strength and elastic modulus of TPV increase with increasing shear rate till the shear-induced PP chain degradation becomes important. Moreover, the tensile strength and elastic modulus of TPV parallel to the shear direction are much higher than those perpendicular to it, while the elongation at break and elasticity are the opposite. Interestingly, for TPV perpendicular to the shear direction, despite of the higher crystallinity and elastic modulus of TPV prepared under moderate shear rate than that under very low shear rate, the elasticity of the former is even much higher than the latter. The mechanisms on effects of shear on the anisotropy of microstructure, mechanical properties and elasticity of EPDM/PP TPV were revealed. This study provides guidance for optimizing process conditions in order to control the microstructure of the TPV and best balance their effects on mechanical properties and elasticity of TPV.</p>

Morphology development of POE/PP thermoplastic vulcanizates (TPVs) during dynamic vulcanization

Synthesis and Characterization of Polyolefin Thermoplastic Elastomers: A Review

Morphological structure of dynamically vulcanized thermoplastic elastomer of ethylene propylene diene monomer/polypropylene

Effect of Additives on the Morphology Evolution of EPDM/PP TPVs During Dynamic Vulcanization in a Twin-Screw Extruder

Properties and Unique Morphological Evolution of Dynamically Vulcanized Bromo-Isobutylene-isoprene Rubber/polypropylene Thermoplastic Elastomer

Effect of Extrusion Process on Properties of POE/PP TPV

Interfacial crystallization and its mechanism in in-situ dynamically vulcanized iPP/POE blends

Dependence of microstructure and properties of polypropylene/bromo‐isobutylene‐isoprene rubber thermoplastic vulcanizates on the molding process

New Understanding of Microstructure Formation of the Rubber Phase in Thermoplastic Vulcanizates (TPV)

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

Theoretical and Experimental Insights into the Phase Transition of Rubber/Plastic Blends During Dynamic Vulcanization

Effect of crosslinking agent dosage on the morphology and properties of thermoplastic vulcanizates based on hydrogenated acrylonitrile butadiene rubber and thermoplastic polyester elastomer

Effects of shear during injection molding on the anisotropic microstructure and properties of EPDM/PP TPV containing rubber nanoparticle agglomerates

Effect of Rubber Nanoparticle Agglomeration on Properties of Thermoplastic Vulcanizates During Dynamic Vulcanization.

Biobased Poly(lactide)/ethylene-co-vinyl Acetate Thermoplastic Vulcanizates: Morphology Evolution, Superior Properties, and Partial Degradability

Unexpected Improvement of Both Mechanical Strength and Elasticity of EPDM/PP Thermoplastic Vulcanizates by Introducing β-Nucleating Agents

PP/EPDM-based Dynamically Vulcanized Thermoplastic Olefin with Zinc Dimethacrylate: Preparation, Rheology, Morphology, Crystallization and Mechanical Properties

Coupling Effect of Molecular Weight and Crosslinking Kinetics on the Formation of Rubber Nanoparticles and Their Agglomerates in EPDM/PP TPVs During Dynamic Vulcanization.

Study on the Preparation and Properties of POE/PP Dynamic Vulcanized Thermoplastic Elastomers with Low Degree of Hardness

Structure and property of IIR/PP thermoplastic vulcanizate. I: Effect of softening agent and filler on structure and property of IIR/PP TPV

Preparation, microstructure, and microstructure-properties relationship of thermoplastic vulcanizates (TPVs): A review