Abstract:The relationships between mechanical loads and bone microstructure are of interest to those who seek to predict bone mechanical properties from microstructure or to predict how organization of bone microstructure is driven by mechanical loads. While strains and displacements in the material are inherently responsible for mechanically caused changes in the appearance of the microstructure, it is the morphometric measures of microstructural organization that are often available for assessment of bone quality. Therefore, an understanding of how strain history is reflected in morphometric measures of bone microstructure has practical implications in that it may provide clinically measurable indices of mechanical history in bone and improve interpretation of bone mechanical properties from microstructural information. The objective of the current study was to examine changes in morphometric measures of cancellous bone microstructure in response to varying levels of continuum level strains. The experimental approach included stereologic analysis of microcomputed tomography (μCT) images of human cancellous bone samples obtained at sequentially increasing levels of strain in a custom-made loading apparatus mounted in a μCT scanner. We found that the degree of anisotropy (DA) decreased from baseline to failure and from failure to postfailure. DA partially recovered from postfailure levels upon unloading; however, the final DA was less than at failure and less than at baseline. We also found that average trabecular thickness (Tb.Th.Av) increased with displacements at postfailure and did not recover when unloaded. Average trabecular number decreased when the specimens were unloaded. In addition, the heterogeneity of Tb.Th as measured by intra-specimen standard deviation (Tb.Th.SD) increased and that of trabecular number (Tb.N.SD) decreased with displacements at postfailure. Furthermore, the intraspecimen coefficient of variation of trabecular number decreased at postfailure displacements but did not recover upon unloading. Finally, the coefficient of variation of trabecular separation at unload was less than that at baseline. These measures can be developed into image-based indices to estimate strain history, damage, and residual mechanical properties where direct analysis of stresses and strains, such as through finite element modeling, may not be feasible. It remains to be determined how wide a time interval can be used to estimate strain history before remodeling becomes an overriding effect on the trabecular architecture.

Loading conditions and bone formation in the GH region of the shoulder.

Bone Geometry on the Contact Stress in the Shoulder for Evaluation of Pressure Ulcers: Finite Element Modeling and Experimental Validation.

The effect of humeral tray thickness on glenohumeral loads in a reverse shoulder 'smart' implant

Finite element analysis part 2 of 2: Glenohumeral bone stress distribution depends on implant configuration for anatomic and reverse stemless shoulder implants

The Influence of Long-Term Shoulder Loading on Sagittal Spino-Pelvic Morphology: a Population-Based Retrospective Study of Chinese Farmers from Radiology

Adaptation to differential loading: comparison of growth-related changes in cross-sectional properties of the human femur and humerus

Influence of Critical Shoulder Angle and Rotator Cuff Tear Type on Load-Induced Glenohumeral Biomechanics: A Sawbone Simulator Study

Computational simulation of bone remodelling post reverse total shoulder arthroplasty

Full‐field experimental analysis of the influence of microstructural parameters on the mechanical properties of humeral head trabecular bone

Mechanical response of local regions of subchondral bone under physiological loading conditions

A gender and size specific evaluation of Grammont-type inlay versus lateralizing onlay stem designs in achieving lateralization and distalization in reverse shoulder arthroplasty

Experimentally Dissociating the Acute Mechanisms of Endplate Fracture Lesions and Schmorl's Node Injuries Using a Porcine Cervical Spine Model

Role of Dynamic Loading on Early Stage of Bone Fracture Healing

Head-Shaft Angle Influences Isometric Shoulder Strength Levels after Intramedullary Nailing of Proximal Humerus Fractures: A Pilot Study

Estimating elbow loading conditions through the motion behaviors of subchondral bone density during joint movements

Morphology properties of scapular spine relative to reverse shoulder arthroplasty: A biomechanical study

Glenoid Concavity Affects Anterior Shoulder Stability in an Active-Assisted Biomechanical Model

Regional characteristics of cortical bone quality in the proximal humerus of postmenopausal women: a preliminary study

Mechanical loading causes detectable changes in morphometric measures of trabecular structure in human cancellous bone

Lines of action and stabilizing potential of the shoulder musculature

Mechanistic study of the effect of flexible fixation and load-bearing stress environment on fracture healing and shaping