Abstract:Pt-modified aluminide coating has attracted great attention due to its advantage of the integrated property in resisting both high temperature oxidation and hot corrosion. By the presence of Pt, the spallation trend of the grown oxide scale and the detrimental effect of S can be restrained at a very low level. Besides, Pt could promote alpha-Al2O3 formation and stabilize beta-NiAl phase. Thus Pt-modified aluminide (Pt-Al) coating has been widely used in some crucial applications requiring reliability and extended service life. There are mainly PtAl2, beta-(Ni, Pt) Al and gamma/gamma'-NiPtAl phases existing inside Pt-Al coating. In this work, a single phase PtAl2 coating was prepared on a Ni-based K38G superalloy through pulse-electroplating of Pt and pack aluminization under stepped heating mode. At 1100 degrees C, the isothermal oxidation behavior of the single phase PtAl2 coating was evaluated by thermogravimetric analysis (TGA). Cyclic oxidation test of the PtAl2 coating was performed within a vertical muffle furnace at the same temperature. The results indicate that the singular PtAl2 coating possesses quite good isothermal oxidation resistance. However, its resistance against cyclic oxidation is very poor. The cyclic stress induced by repeated heating and cooling has caused visible detachment of PtAl2 coating layer, and the spallation of PtAl2 in further would lead to a premature failure of the whole coating system. Partial spallation of PtAl2 layer, including undesirable consumption of Al inside beta-NiAl nearby the spallation acts the main reason responsible for the final failure. Accordingly, it is not appropriate to apply single phase PtAl2 coating in the high temperature services involving stress and load. The degradation mechanism of the singular PtAl2 coating is investigated by discussing the stress generated from cyclic heating and cooling.

Corrosion-spots Arising from Aluminide Coating on DZ40M Alloy during High-temperature Oxidation in Air

Failure Behavior of an Aluminide Coating on a Co-Base Superalloy during High-Temperature Oxidation in Air

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

Main Degradation Way of Aluminide Coating on Co-base Superalloys Oxidized in Air at High Temperatures

Influence factors of high temperature oxidation for Pt-modified-aluminide bond coatings

Oxidation Behavior and Breakdown of an Aluminide Coating on DZ40M Alloy at High Temperatures

High-temperature oxidation behavior of aluminide coatings on a new cobalt-base superalloy in air

Cyclic Oxidation Behavior of the Aluminide Coatings on the Co-Base Superalloy DZ40M

HIGH TEMPERATURE OXIDATION OF DZ40M ALLOY

High-Temperature Oxidation Behavior of the Co-Base Superalloy DZ40M in Air

CORROSION BEHAVIOR OF SUPER-AUSTENITIC STAINLESS STEEL AL-6XN IN SUPERCRITICAL WATER

Research Progress on High-Temperature Oxidation and Corrosion Mechanisms of Aluminide Coatings

Microstructure Evolution and Failure Mechanism of Cr-coated Zry-4 in Air and Steam at 1200 °C

HIGH-TEMPERATURE OXIDATION AND DEGRADATION LAWS OF ALUMINIDE COATING ON COBALT-BASE SUPERALLOYS

High-temperature steam oxidation behavior and failure mechanisms of Al alloyed Cr coatings on Zr-4 alloy

High-temperature Corrosion Behaviour of Pt-modified Aluminide Coating with Solid NaCl Deposit in O2 + 10 Vol% H2O and the Influence of Pre-Oxidation Treatment

High-temperature Oxidation Lifetime Prediction for Aluminide Coatings in Air

Oxidation Property and Failure Mechanism of A Single Phase Ptal2 Coating

Effect of Ti on Aluminide Coating for DZ40M Alloy

Research on Hot Corrosion Behavior of DZ40M and K452 Superalloys in NaCl Molten Salt

Failure mechanism of MCrAlY coating at the coating‐substrate interface under type I hot corrosion