Abstract:This study employs the response surface method to optimize the mixture design of superhydrophobic foamed concrete. The study investigates the influence of calcium stearate (CS, dosage 1 %similar to 5 %), polydimethylsiloxane (PDMS, dosage 2 %similar to 8 %), and hydroxypropyl methylcellulose (HPMC, dosage 0.05 %similar to 0.2 %) on various properties of foamed concrete, including density, compressive strength, contact angle, and water absorption. Additionally, the research explores the application of superhydrophobic foamed concrete in integrated roofing systems and assesses its thermal and structural performance through finite element analysis. Results reveal that foamed concrete achieves a contact angle greater than 150 degrees when formulated with a mix ratio of CS (3 %), PDMS (8 %), and HPMC (0.05 %), or CS (3 %), PDMS (5 %), and HPMC (0.125 %). A negative linear correlation between the heat transfer coefficient and the thickness of foamed concrete is found. Furthermore, the heat transfer coefficient is inversely related to the spacing between the concave and convex drainage boards. Specifically, for a toe spacing of 50 mm and foamed concrete thickness exceeding 70 mm, the heat transfer coefficient of the roof measures 0.788 W/(m(2)K). When the roof thickness increases from 70 mm to 100 mm, the roof heat transfer coefficient drops to 0.69 W/(m(2)center dot K). When the toe spacing is increased from 50 mm to 60 mm, the heat transfer coefficient of the roof drops sharply to about 0.66 W/(m(2)center dot K) at the thickness of 50 mm. The insulation requirements for the roof are satisfactorily met to 0.8 W/(m(2)K). Under applied roof loads, the maximum von Mises stress experienced by the integrated roof is 0.6 MPa at a toe spacing of 50 mm. With the increase of the roof thickness, the maximum value of the DAMAGEC damage coefficient gradually decreases from 0.3 to 0.17. The maximum damage position has always been at the weak position of the four corners, which is consistent with the actual use status. The research findings on superhydrophobic foamed concrete have significant theoretical and engineering application value. Moreover, the construction of an "insulation/hydrophobic integrated" roof system demonstrates the feasibility of an integrated roof system and the potential for insulation/hydrophobic integration in roof system construction.

Research on waterproof and thermal insulation roofing board

The research for new material and new technology of exterior walls thermal insulation

Preparation and Properties of Expanded Vermiculite/Gypsum Thermal Insulation Boards

Development and application of inorganic-organic compound thermal insulating mortar

Effect of waterproof agent on performance of inorganic lightweight aggregate thermal insulating mortar

Weathering of Roofing Insulation Materials under Multi-Field Coupling Conditions

Superhydrophobic Foamed Concrete Based on Response Surface Method: Mix Design and Its Potential Application in Roofing Systems

Pore Structure, Hardened Performance and Sandwich Wallboard Application of Construction and Demolition Waste Residue Soil Recycled Foamed Concrete

Preparation and Characterization of the One-Piece Wall Ceramic Board by Using Solid Wastes

Experimental research on a feasible rice husk/geopolymer foam building insulation material

Study on the Preparation and Performance of Lightweight Wallboards from MSWIBA Foam Concrete

Integrated Utilization of Fly Ash and Waste Glass for Synthesis of Foam/dense Bi-Layered Insulation Ceramic Tile

Renewable Insulation Panels Made with Cynodon Dactylon Grass for Building Applications: Physical, Mechanical, Acoustic, and Thermal Properties

Development and performance evaluation of alkali-activated multiple solid waste-based building foam insulation materials

A foamed cement blocks with paraffin/expanded graphite composite phase change solar thermal absorption material

On Thermal Insulation Properties of Various Foaming Materials Modified Fly Ash Based Geopolymers

Application Research of a Biomass Insulation Material: Eliminating Building Thermal Bridges

Development of Asphalt Emulsion-Polystyrene Grain Thermal Insulation Mortars

Study on the Mechanical Properties of Fly-Ash-Based Light-Weighted Porous Geopolymer and Its Utilization in Roof-Adaptive End Filling Technology

Preparation of Glass Ceramic Foams for Thermal Insulation Applications from Coal Fly Ash and Waste Glass

Preparation and properties of silicate inorganic exterior wall insulation based on thermal energy storage