Abstract:Cu2O/CuO bilayers were fabricated by electrodeposition of the CuO layer in a copper(II)-ammonia complex aqueous solution, followed by photoelectrochemical deposition of the Cu2O layer at potentials ranging from -0.3 to -1.0 V referenced to a Ag/AgCl electrode in a copper(II)-lactate complex aqueous solution under light irradiation, and the effects of varied potentials of the photoelectrochemical Cu2O depositions and post-heating conditions on their structural, optical, and photovoltaic characteristics were investigated with X-ray diffraction, field emission-scanning electron microscopy, optical absorption measurements, and external quantum efficiency (EQE) measurements with and without applied bias voltage. The Cu2O layers with a characteristic 2.1 eV band gap energy were adhesively stacked on the thorn-like grains of the CuO layers possessing a characteristic 1.5 eV band gap energy, and dense and defect-free Cu2O/CuO bilayers could be fabricated at the potentials of -0.4 and -0.5 V, but the grain size of Cu2O decreased at -0.5 V. In addition, the metallic Cu was deposited simultaneously at potentials less than -0.7 V. The Cu2O/CuO bilayer fabricated at -0.4 V revealed photovoltaic features at wavelengths ranging from 350 nm to approximately 900 nm, and a maximum EQE value of 56.8% was achieved at 510 nm in wavelength with a bias voltage of -0.1 V. The maximum EQE value, however, decreased to 1.2% accompanied with the peak wavelength shift to 580 nm, and no photovoltaic feature was observed at potentials of -0.3, -0.7, and -1.0 V. The photovoltaic performance for the Cu2O/CuO bilayer fabricated at -0.4 V was ameliorated by heating at 423 K, and the maximum EQE values were enhanced to 87.7% at 550 nm and 89.8% at 530 nm in an ambient atmosphere and vacuum. Both the Cu2O and CuO layers acted as photovoltaic layers in the Cu2O/CuO bilayer fabricated at -0.4 V and heated at 423 K, and the electrical characteristic including the carrier mobility affected the photovoltaic performance. The photovoltaic feature, however, disappeared by heating above 523 K due to the formation of nanopores inside the CuO layer and near the CuO heterointerface to the Cu2O and fluorine-doped tin oxide substrate.

Electrodeposited Cu2O As Photoelectrodes with Controllable Conductivity Type for Solar Energy Conversion

CuBi2O4/CuO Heterojunction Coated with Electrodeposited ZnO Overlayer for Stable Solar Hydrogen Evolution

Electrodeposited Cu2O on the {101} Facets of TiO2 Nanosheet Arrays and Their Enhanced Photoelectrochemical Performance

BiVO4 photoelectrodes for unbiased solar water splitting devices enabled by electrodepositing of Cu2O simultaneously as photoanode and photocathode

Electrodeposition of Copper Oxides as Cost-Effective Heterojunction Photoelectrode Materials for Solar Water Splitting

Tuning Band Gaps and Photoelectrochemical Properties of Electrodeposited CuO Films by Annealing in Different Atmospheres

A Method for Synthesis of Renewable Cu2o Junction Composite Electrodes and Their Photoelectrochemical Properties

Electrochemically Deposited Cu2O on TiO2 Nanorod Arrays for Photovoltaic Application

Optimization of Photoelectrochemical Performance in Pt-modifie Dp-Cu2o/n-cu2o Nanocomposite

Rational design and fabrication of Cu2O film as photoelectrode for water splitting

Embedment of Anodized P-Type Cu2O Thin Films with CuO Nanowires for Improvement in Photoelectrochemical Stability

Cu 2 O/CuO composite for efficient performance in photoelectrochemical and optoelectronics applications

Reversible Chemical Tuning of Charge Carriers for Enhanced Photoelectrochemical Conversion and Probing of Living Cells

Semitransparent Cu2O films based on CuO Back Layer for Photoelelctrochemical Water Splitting and Photovoltaic Applications

Solar Energy Conversion and Electron Storage by a Cu2O/CuO Photocapacitive Electrode

3D Cathodes of Cupric Oxide Nanosheets Coated onto Macroporous Antimony-Doped Tin Oxide for Photoelectrochemical Water Splitting

3D-printed Cu2O photoelectrodes for photoelectrochemical water splitting

Novel application of electrochemical test for the controllable electrodeposition of Cu 2 O and metallic Cu film

Cu2O Photocathodes for Unassisted Solar Water-Splitting Devices Enabled by Noble-Metal Cocatalysts Simultaneously As Hydrogen Evolution Catalysts and Protection Layers

Engineering the Interface of Cu/MoS 2 Nanostructures for Improved Charge Transfer for Applications as PEC Anode Materials

Photoelctrochemically Fabricated and Heated Cu2O/CuO Bilayers with Enhanced Photovoltaic Characteristics