Abstract:The deformation behavior of a radially forged 2A50 aluminum alloy was investigated by thermal compression test at high-temperature solid (300–500 °C) and semi-solid (565–585 °C) states with strain rates of 0.01–0.5s–1. A strain-compensated Arrhenius constitutive equation was established to describe the relationship between flow stress and compression parameters. The inhomogeneous deformation and microstructure evolution of the specimen were explored. Results reveal that the strain-compensated Arrhenius model can accurately predict experimental flow stress in both two temperature states. In the high-temperature solid state, the equilibrium between the softening effect (dynamic recovery and dynamic recrystallization) and work hardening leads to a steady stage of the flow curves after peak. In the semi-solid temperature, the softening mechanisms mainly include the high level of dynamic recrystallization (DRX), lubrication of liquid phases, and partial collapse of solid-phase skeleton, contributing to a declining stage of flow stress after peak. Strain and temperature profoundly influence DRX. At high-temperature solid state, coarse and elongated grains predominate in the regions with small strain, whereas DRX and numerous subgrains massively occur in the regions with large strain. The entire sample compressed in semi-solid temperature is subjected to DRX, attributed to the elevated temperature compared to the high-temperature solid state. Fine DRX grains are concentrated at the center of the large deformation zone (with large strain) due to the frequent DRX. Elevating semi-solid temperature leads to the formation of large equiaxed grains. DRX facilitates the weakening of deformed textures, demonstrated by the presence of deformed textures (<111> and <100>//X0 fiber textures, <111>//Z0 fiber texture, and {110}<111> texture) in the sample at high-temperature solid state, contrasted with the absence of pronounced preferred orientation in semi-solid compressed sample.

Constitutive Behavior of Aluminum Alloy in a Wide Temperature Range from Warm to Semi-Solid Regions

Study on Correlation Between Parameters of "single Factor" Constitutive Model and Temperature for 7050 Aviation Aluminum-Alloy

Research on the Constitutive Equation of 6061 Aluminum Alloys in the Hot Compressive Deformation

Constitutive modeling of deformation in high temperature of a forging 6005A aluminum alloy

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

Intermediate temperature tensile behavior and processing map of a spray formed 7075 aluminum alloy

Research on High-Temperature Constitutive Relationship of Aluminum Alloy

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Unified Constitutive Model of Aluminum Alloy 2219 at Elevated Temperature

Constitutive Modeling of the Hot Deformation Behavior in 6082 Aluminum Alloy

Constitutive Model of Thixo-Compression Deformation of 6063 Aluminum Alloys

Hot Tensile Behavior of an Extruded Al–Zn–Mg–Cu Alloy in the Solid and in the Semi-Solid State

Liquid Phase Behavior during Elevated Temperature Deformation of the Fine-Grained 5083 Al Alloy

A Physically-Based Constitutive Modelling of a High Strength Aluminum Alloy at Hot Working Conditions

Research and Revise on Constitutive Equation of 7050-T7451 Aluminum Alloy in High Strain Rate and High Temperature Condition

Constitutive model for hot deformation of aluminum alloy

Constitutive modeling and microstructure characterization of 2196 Al-Li alloy in various hot deformation conditions

Deformation Behavior and Microstructure Characterization of the Radially Forged 2A50 Aluminum Alloy at High-Temperature Solid and Semi-Solid States

Tensile Properties of As-Deformed 2A50 Aluminum Alloy in Semi-Solid State

Investigation of Tensile Deformation Behavior of 7075-T6 at Elevated Temperatures

Constitutive behavior of as-cast A356