Abstract:Over the past years, perylenediimide (PDI)-based polymers have emerged as one of the widely studied polymer acceptors applicable to all-polymer solar cells (PSCs) due to their outstanding photovoltaic properties. Covalently fused PDI units, such as naphthodiperylenetetraimide (NDP), are proven beneficial to increasing the regularity of polymer backbones and enhancing the molecular packing in blend films, thus optimizing the active-layer morphology and improving the device performance. However, most investigated PDI polymers commonly demonstrated low open-circuit voltage (V-oc) in solar cells due to their low-lying lowest unoccupied molecular orbital (LUMO), which greatly limited the power-conversion efficiencies (PCEs) of their devices. Herein, we design and synthesize two new polymer acceptors (PTP-TT and PTP-Th) using thiophene-fused dimeric PDI (i.e., PTP) as the key building block. Both polymers exhibit much elevated LUMO levels at ca. -3.8 eV and achieve higher V-oc in devices compared with NDP-derived polymers. In particular, PTP-TT exhibits stronger light-absorption ability than PTP-Th and a presumably more planar backbone conformation, which are favorable for molecular packing and charge carrier transport in the active layer. Using PTB7-Th as the donor, PTP-TT-based devices achieve the best PCE of 7.04%, with a V-oc of 0.86 V, a short-circuit current density of 14.96 mA/cm(2), and a fill factor of 54%. The current results demonstrate that fusing PDIs with a proper electron-rich moiety can synergistically elevate the LUMO level and optimize the backbone regularity of polymer acceptors to obtain desirable efficiencies of PSCs.

Aromatic‐Diimide‐Based N‐type Conjugated Polymers for All‐Polymer Solar Cell Applications

Acceptor–acceptor conjugated copolymers based on perylenediimide and benzothiadiazole for all‐polymer solar cells

Comparison of three n-type copolymers based on benzodithiophene and naphthalene diimide /perylene diimide/fused perylene diimides for all-polymer solar cells application.

Dye-incorporated Polynaphthalenediimide Acceptor for Additive-free High-performance All-polymer Solar Cells.

Recent Research Progress of n-Type Conjugated Polymer Acceptors and All-Polymer Solar Cells

Crystallinity and Orientation Manipulation of Anthracene Diimide Polymers for All‐Polymer Solar Cells

N‐type Conjugated Polymer Based on Dicyanodistyrylbenzene and Naphthalene Diimide Units for All‐Polymer Solar Cells

Perylene Diimide Based Isomeric Conjugated Polymers As Efficient Electron Acceptors for All-polymer Solar Cells

Novel Perylene Diimide Based Polymeric Electron-Acceptors Containing Ethynyl As the Π-Bridge for All-Polymer Solar Cells

Recent Progress in All‐Polymer Solar Cells Based on Wide‐Bandgap P‐type Polymers

Naphthalenediimide-based N-Type Polymer Acceptors with Pendant Twisted Perylenediimide Units for All-Polymer Solar Cells

Rational Design of Perylenediimide-Based Polymer Acceptor for Efficient All-Polymer Solar Cells

Polymer acceptor based on naphthalene diimide and diethynylbenzo[1,2-b:4,5-b'] dithiophene units for efficient all-polymer solar cells

Star-like N-Type Conjugated Polymers Based on Naphthalenediimide for All-Polymer Solar Cells

Conjugated Donor–Acceptor Terpolymers Toward High‐Efficiency Polymer Solar Cells

Novel Perylene Diimide-Based Polymers with Electron-Deficient Segments As the Comonomer for Efficient All-Polymer Solar Cells

Rational design of conjugated side chains for high-performance all-polymer solar cells

Asymmetric Alkyl Side-Chain Engineering of Naphthalene Diimide-Based N-Type Polymers for Efficient All-Polymer Solar Cells.

Thiophene-Fused Perylenediimide-Based Polymer Acceptors for High-Performance All-Polymer Solar Cells

Fused Perylene Diimide-Based Polymeric Acceptors for Efficient All-Polymer Solar Cells

High-Performance All-Polymer Solar Cells Achieved by Fused Perylenediimide-Based Conjugated Polymer Acceptors.