Abstract:The surface modification of continuous fiber was conducted by the inductive coupling radio frequency cold plasma (ICP) technique. The influence of the plasma parameters, such as treatment time, discharge pressure, power, etc. on the surface chemical composition,surface morphology,surface roughness and surface free energy of continuous fiber was systematically studied by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and dynamic contact angle analysis (DCAA), respectively. Results showed that the plasma treatment introduced some polar groups such as 0 C 0 onto the continuous fiber surface, increasing the percentage of surface polar groups; the plasma etched the fiber surface obviously,enhancing the surface roughness and surface free energy and improving the wettability of the fiber distinctly. Plasma treatment conditions should be appropriate during surface modification of fibers by clod plasma. After CF was treated for 5 min,CF surface polar group was increased to a relatively higher level. However,the effect of plasma etching on CF surface is relatively slower. After CF was treated for 5 min,CF surface roughness was changed a little. However, after CF was treated for more than 15 min CF surface roughness was increased significantly. Based on the study above, the interfacial adhesion and fracture mechanism of continuous fiber reinforced soluble polyaromatic ether resin composites was also systematically analysed by interlaminar shear strength (ILSS), water absorption and scanning electron microscopy (SEM) measurements. It was found that CF reinforced poly(phthalazinone ether sulfone ketone) (PPESK) composite interfacial adhesion mechanism analysis indicats that both chemical bonding and mechanical interlocking interaction has a positive effect on composite interfacial adhesion, however, mechanical interaction has a dominant effect on composite interfacial adhesion than chemical bonding interaction. Armos aramid fiber composite interlaminar, shear strength increased from 59. 5 MPa for untreated sample to 68. 8 MPa for plasma treated for 10 min under discharge power at 200 W, with an increase of 15. 6%. The water absorption decrease of composite also indirectly showed that oxygen plasma treatment improved composite interfacial adhesion. The primary failure mode of Armos aramid or PBO/PPESK composites shifted from interface failure to matrix fracture after oxygen plasma treatment. The interfacial adhesion of Armos aramid or PBO/PPESK composites was improved by oxygen plasma treatment due to the chemical linkage and mechanical bonding between Armos aramid or PBO fibers and PPESK matrices, and the chemical linkage effect exhibits more contribution than the mechanical bonding.

Enhanced interfacial adhesion of aramid fiber III reinforced epoxy composites via low temperature plasma treatment

Influence of Argon Plasma Treatment on Interfacial Performance of CFRP at High Temperature

Improvement of aramid fiber III reinforced bismaleimide composite interfacial adhesion by oxygen plasma treatment

Effects of Air Plasma Modification on Aramid Fiber Surface and Its Composite Interface and Mechanical Properties

Effect of Low-Temperature Plasma Surface Treatment on Bonding Properties of Single-Lap Joint of Thermosetting Composites

Interfacial adhesion and shear behaviors of aramid fiber/polyamide 6 composites under different thermal treatments

Effects of oxidation‐induced aggregation structure transformation of aramid fiber on interfacial adhesion of epoxy resin

Enhancing the Interfacial Strength of Carbon Fiber/Poly(ether ether ketone) Hybrid Composites by Plasma Treatments.

Effects of argon plasma treatment on carbon fiber surface characteric and its reinforcing polyimide composites interfacial properties at room and elevated temperatures

A Study of the Effect of Oxygen Plasma Treatment on the Interfacial Properties of Carbon Fiber/epoxy Composites

The Influence of Plasma Surface Treatment of Carbon Fibers on the Interfacial Adhesion Properties of UHMWPE Composite

The Ultrasound‐based Interfacial Treatment of Aramid Fiber/epoxy Composites

INTERFACIAL STUDIES OF CONTINUOUS FIBERS REINFORCED POLY(AROMATIC ETHERS) CONTAINING PHTHALAZINONE MOIETIES

Investigations on the effect of plasma treatment on the adhesive bonding behavior of ultra high modulus K13C2U/cyanate ester fiber composites

Surface Activation and Characterization of Basalt Fiber by Plasma Treatment and Its Interfacial Adhesion with Epoxy

Effects of Oxygen Plasma Treatment on Domestic Aramid Fiber III Reinforced Bismaleimide Composite Interfacial Properties

Interfacial Bonding Enhancement Between Cryogenic Conditioned Carbon Fiber and Epoxy Resin Characterized by the Single-Fiber Fragmentation Method

Interface Characteristic Of Aramid Fiber Reinforced Poly(Phthalazinone Ether Sulfone Ketone) Composite

Effect Of Air Plasma Treatment On Interfacial Shear Strength Of Carbon Fiber-Reinforced Polyphenylene Sulfide

Strengthening the Interface Between Individual Aramid Fibers and Polymer at Room and Elevated Temperatures

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites