Abstract:Surface preparation of ultra-high modulus fiber composites for adhesive bonding is challenging due to the subsurface damages that can occur during a standard abrasion operation that could weaken the laminate cohesion. Therefore, it is highly desirable to utilize a non-contact method that can clean and activate the composite surface without exerting an external force to eliminate potential damage. This investigation focuses on the use of atmospheric plasma treatment (APT) for the surface preparation of unidirectional ultra-high modulus, composites for adhesive bonding. The laminates were manufactured using Mitsubishi K13C2U pitch-based carbon fiber with Tencate's RS-3C cyanate-ester resin and bonded with Henkel 9394 epoxy. Surface analysis of plasma-treated samples revealed a significant reduction of surface contamination and increased chemical modification of the matrix material resulting in improved wetting and the formation of chemical groups conducive to bonding. The plasma treatment also produced a minor increase in surface roughening, well below levels expected to contribute to mechanical interlocking. APT epoxy-bonded lap-shear specimens (LSS) exhibited a 50% increase in strength as compared to mechanically abraded samples. It was also shown that solvent rinsing after APT removed a highly-oxidized, poorly bonded carbonate component from the treated resin surface as evidenced by XPS. This surface ash is observed at fairly high concentrations after APT of cyanate ester resin composites limiting functional group contributions. The removal of this ash resulted in increases in LSS of 25% as compared to unrinsed APT surfaces. Lap shear strengths and GIC delamination resistance tests showed improvements over abrasion surface treated samples. Image analysis of the fracture faces for both surface treatments showed that abrasion treated surfaces resulted in sub-surface damage to the fibers that translated into brittle fracture through weak, highly aligned layers within these graphitic fibers. On the other hand, plasma treatment was successfully applied to minimize subsurface damage and resulted in crack propagation along with the more tortuous fiber-matrix interface. The degree of the improvements was ultimately limited by the interlaminar strength of these composites.

Improvement of aramid fiber III reinforced bismaleimide composite interfacial adhesion by oxygen plasma treatment

Enhancing CFRP Laminates with Plasma Jet Arrays: A Study of Interlaminar Mechanical Properties

Evaluation of Interfacial Properties of Atmospheric Pressure Plasma-Treated Cnt-Phenolic Composites by Dual Matrix Fragmentation and Acoustic Emission Tests

Enhanced Interfacial Properties of High-Modulus Carbon Fiber Composites Via Molecular Assembly on Fiber Surface

Effects of argon plasma treatment on carbon fiber surface characteric and its reinforcing polyimide composites interfacial properties at room and elevated temperatures

Surface modification of polyimide fibers for high-performance composite by using oxygen plasma and silane coupling agent treatment

Carbon Fiber Surface Modification by Plasma Treatment for Interface Adhesion Improvements of Aerospace Composites

Effects of Air Plasma Modification on Aramid Fiber Surface and Its Composite Interface and Mechanical Properties

Surface Modification and Mechanical Properties Improvement of Bamboo Fibers Using Dielectric Barrier Discharge Plasma Treatment

Surface Activation and Characterization of Basalt Fiber by Plasma Treatment and Its Interfacial Adhesion with Epoxy

Surface Ammonification Of The Mutual-Irradiated Aramid Fibers In 1,4-Dichlorobutane For Improving Interfacial Properties With Epoxy Resin

Improvement of the Mechanical Properties by Surface Modification of ZnCl2 and Polydopamine in Aramid Fiber Composites

Surface Modification of Aramid Fiber by Cascade Process with Atmospheric Plasma and TDI Grafting

Investigations on the effect of plasma treatment on the adhesive bonding behavior of ultra high modulus K13C2U/cyanate ester fiber composites

Synergetic enhancement of interfacial properties and impact resistant of UHMWPE fiber reinforced composites by oxygen plasma modification

Synergetic surface modification of 3D braided carbon fiber-reinforced composites for enhancing mechanical strength

Comparative studies of nitrogen plasma and argon plasma treatment on the strength of PBO fibre reinforced high-temperature resistant thermoplastic composite

Enhancing the bond strength between glass fibre reinforced polyamide 6 and aluminium through μPlasma surface modification

Interfacial modification to improve the mechanical performance of basalt fiber/epoxy 3D woven composites

Improving the Interfacial Adhesion of Long Carbon Fiber-Reinforced Polyamide 6 Composites by Electrochemical Oxidation and Polyethylenimine-Carboxymethyl Cellulose Grafting

Augmented interlaminar fracture toughness of nanofibers-interleaved composite laminates via plasma treatment