Abstract:Selective laser melting (SLM) technology was employed for the additive manufacturing of Ti-5Al-2.5Sn alpha titanium alloy in this work and the influences of laser energy input on densification behavior, microstructure evolution and mechanical performances of the as-deposited products were investigated. It was found that the relatively high volumetric energy densities (VEDs) of 167-417 J/mm(3) resulted in large quantities of keyhole-induced spherical pores whereas the relatively low VEDs of 51-83 J/mm(3) led to notable lack-of-fusion defects. At the proper VED of 125 J/mm(3), highly densifled products with internal porosity of merely 0.05% were obtained. At the relatively high VEDs of 167-417 J/mm(3), as-built samples presented duplex microstructures composed of acicular alpha' martensites and bulk alpha(M) massive grains. In contrast, overwhelmingly martensitic microstructures were formed at lower VEDs of 51-125 J/mm(3). The martensitic microstructure exhibited a unique hierarchical feature, which could be explained using the theory of athermal martensitic transformation kinetics. With the decrease of VED from 417 J/mm(3), the average size of alpha' needles increased first, then came to its plateau at the VEDs of 167-208 J/mm(3), and decreased again at the VEDs of 51-167 J/mm(3). At the VEDs of 167-417 J/mm(3), the formation of spherical pores and bulk alpha(M) grains resulted in relatively poor tensile properties. At the VEDs of 51-83 J/mm(3), the formation of lack-of-fusion defects masked the enhanced fine-grain strengthening effect provided by the much refined alpha' needles and the decrease in the fraction of bulk alpha(M), thus also leading to very limited tensile properties. At the proper VED of 125 J/mm(3), as-built tensile properties reached to their peak with ultimate tensile strength of 1173 MPa, yield strength of 1061 MPa, and elongation of 7.7%. This can be attributed to the high densification degree, the almost complete vanish of bulk alpha(M) grains, and the moderate size of alpha' needles. (C) 2018 Elsevier B.V. All rights reserved.

Densification, Microstructure Evolution and Fatigue Behavior of Ti-13Nb-13Zr Alloy Processed by Selective Laser Melting

Microstructure and Mechanical Performance Tailoring of Ti-13Nb-13Zr Alloy Fabricated by Selective Laser Melting after Post Heat Treatment

Anisotropic Mechanical Behavior of Biomedical Ti-13Nb-13Zr Alloy Manufactured by Selective Laser Melting

Microstructure Evolution and High Strength-Ductility Synergy of Ti-13Nb-13Zr-2Ta Alloy Fabricated by Laser Powder Bed Fusion

Microstructure and Mechanical Properties of Selective Laser Melted Biomaterial Ti-13Nb-13Zr Compared to Hot-Forging

Effect of Laser Energy Density on Microstructural Evolution of Selective Laser Melted Ti-15Zr Alloy

Densification Behavior, Microstructure Evolution, and Mechanical Performances of Selective Laser Melted Ti-5Al-2.5Sn Α Titanium Alloy: Effect of Laser Energy Input

Research on Selective Laser Melting of Ti6Al4V: Surface Morphologies, Optimized Processing Zone, and Ductility Improvement Mechanism

Effect of Process Parameters on the Microstructure and Properties of Cu–Cr–Nb–Ti Alloy Manufactured by Selective Laser Melting

Texture Evolution, Phase Transformation and Mechanical Properties of Selective Laser Melted Ti-13Nb-13Zr

High-strength and thermally stable TiB2-modified Al–Mn–Mg–Er–Zr alloy fabricated via selective laser melting

Microstructure and Mechanical Property of Ti–5Al–5Mo–5V–3Cr–1Zr Alloy Fabricated by Selective Laser Melting with a Preheated Substrate

Mechanical and Corrosion Behavior of Titanium Alloys Additively Manufactured by Selective Laser Melting – A Comparison Between Nearly Β Titanium, Α Titanium and Α + Β Titanium

Balanced Strength-Ductility Combination and Good Recoverable Strain of Ni50.7Ti49.3 Alloy Fabricated by High Scanning Velocity in Selective Laser Melting

In Situ Fabrication of a Titanium-Niobium Alloy with Tailored Microstructures, Enhanced Mechanical Properties and Biocompatibility by Using Selective Laser Melting

A Nb521 Alloy Processed by Selective Laser Melting: Microstructure and Tensile Properties

Effect of Laser Scanning Speed on a Ti-45Al-2Cr-5Nb Alloy Processed by Selective Laser Melting: Microstructure, Phase and Mechanical Properties

Crystal Growth Mechanism and Mechanical Properties of Ti-6Al-4 V Alloy During Selective Laser Melting

Tensile property and microstructure of Al−4.77Mn−1.37Mg−0.67Sc−0.25Zr alloy under different selective laser melting processing parameters

Study on Fatigue Behavior and Fracture Mechanism of LMD Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Alloy Based on Microstructure

A Novel Titanium Alloy Manufactured by Selective Laser Melting: Microstructure, High Temperature Oxidation Resistance