Abstract:Microcellular foaming with CO2 and N2 as co‐blowing agents is developed to achieve mechanically robust PEBA foams by reducing the dimensional shrinkage. Compared with pure CO2 as blowing agents, the co‐blowing agents leads to significantly reduced shrinkage of PEBA foams after foaming and hence improved mechanical performance. The promising outcome paves way for developing high‐performance thermoplastic elastomer foams. Polyether block amide (PEBA) is an important thermoplastic polyester elastomer (TPE) owing to its low density and high resilience. Microcellular foaming can endow PEBA with significant potential in sports, medical, and industrial applications. However, with the current microcellular foaming technology, it remains challenging to obtain PEBA foams with stable shapes, which are critical for their mechanical properties. Therefore, microcellular foaming with CO2 and N2 as co‐blowing agents is utilized in this study to achieve mechanically robust PEBA foams by reducing the dimensional shrinkage. The introduction of N2 can effectively slow the diffusion rate of blowing agents into the air, providing support for the foam to resist external atmospheric pressure and effectively reducing the dimensional shrinkage of PEBA foams. Consequently, a stable foam shape is achieved with an expansion ratio of 7.9. Finally, the PEBA foams with excellent shrinkage resistance and mechanical properties are prepared, and the cell shrinkage mechanism is analyzed to study the effects of blowing agents and foaming methods on the structural evolution of TPE foams. This promising outcome paves way for their practical industrial applications.

HDPE/UHMWPE Composite Foams Prepared by Compression Molding with Optimized Foaming Capacity and Mechanical Properties

Enhanced Strength and Foamability of High-Density Polyethylene Prepared by Pressure-Induced Flow and Low-Temperature Crosslinking

Enhanced Foaming Behavior of Ultrahigh Molecular Weight Polyethylene by Blending Silicone Powder in Microcellular Foaming

Tailored Morphologies and Properties of High-Performance Microcellular Poly(phenylene Sulfide)/poly(ether Ether Ketone) (PPS/PEEK) Blends

Preparation and properties of polyimide/chopped carbon fiber composite foams

Preparations and Characterizations of High Density Polyethylene/ultra-High Molecular Weight Polyethylene Composite

Effects of Process Conditions and Nano-Fillers on the Cell Structure and Mechanical Properties of Co-Injection Molded Polypropylene-Polyethylene Composites

Improving of Cell Structure of Microcellular Foams Based on Polypropylene/High-density Polyethylene Blends

Fabrication of Lightweight Polyphenylene Oxide/High‐Impact Polystyrene Composite Bead Foam Parts via In‐Mold Foaming and Molding Technology

Poly(ether imide)/Epoxy Foam Composites with a Microcellular Structure and Ultralow Density: Bead Foam Fabrication, Compression Molding, Mechanical Properties, Thermal Stability, and Flame-Retardant Properties

Extrusion Foaming Behavior of Different High Density Polyethylene Foaming Systems

In-Situ Bubble Stretching Assisted Melt Extrusion for the Preparation of HDPE/UHMWPE/CF Composites

High Thermal Insulation and Compressive Strength Polypropylene Foams Fabricated by High-Pressure Foam Injection Molding and Mold Opening of Nano-Fibrillar Composites

Biodegradable and Ultra-High Expansion Ratio PPC-P Foams Achieved by Microcellular Foaming Using CO2 as Blowing Agent

Enhancing the Sound and Thermal Insulation Properties of Polypropylene Foam by Preparing High Melt Strength Polypropylene

Preparation of high-expanded PP foams with chemical blowing process

Super‐Elastic and Dimensionally Stable Polyether Block Amide Foams Fabricated by Microcellular Foaming with CO2&N2 as Co‐Blowing Agents

Wood‐thermoplastic Composites from Wood Flour and High‐density Polyethylene

Preparation of Acrylamide‐based Poly‐hipes with Enhanced Mechanical Strength Using PVDBM‐b‐PEG‐emulsified CO2‐in‐water Emulsions

Microcellular foaming of PP/PE blends with different viscosity and elasticity

Synergic Enhancement of High-density Polyethylene Through Ultrahigh Molecular Weight Polyethylene and Multi-flow Vibration Injection Molding: A Facile Fabrication with Potential Industrial Prospects