Abstract:This paper introduces an asynchronous-pouring-construction (APC) technology for long-span prestressed concrete (PC) box girder bridges with corrugated steel webs (CSWs). The technology makes full use of the CSWs to support the hanging basket. The top slabs, bottom slabs and CSWs are divided into multiple independent working platforms to improve the construction efficiency. In present study, the authors conducted a theoretical analysis of the deflection in PC girder bridges with CSWs using APC technology. A simplified deflection calculation model was developed on the basis of the principle of section equivalence for different segment division. Consequently, a series of theoretical formulas was proposed considering additional shear deflection induced by bending moments. These formulas could be utilised to calculate the configuration and the total deflection of the bridge during APC process, facilitating the pre-camber application to eliminate the deflection and to ensure the closure of the bridge. Moreover, parallel finite element analyses (FEA) and field monitoring tests were conducted to validate the simplified calculation method. The comparison results showed that the calculated deflections using the simplified method agreed well with the FEA and test results. The proportion of shear deflection in the total deflection ranged from 17% to 39% from the forward movement of basket to the pouring slabs, the shear deflection could not be negligible. The segments' length had large effect on the deflection of the CSWs with 50 mm at the maximum cantilever state in this bridge case study, and the deflection induced by the pouring concrete of the slabs accounted for approximately 70% of the total deflection. The additional shear deformation due to bending moment at the end of area A (composite section with both concrete top and bottom slabs and CSWs) was basically the same as that in area B (composite section with bottom slab and CSWs). Therefore, the simplified method which takes into account the additional shear deformation of the segments in area A without considering area B was able to satisfy the engineering accuracy. In short, in comparison to traditional analytical methods and FEA, the proposed method could predict the deflection more efficient within accept accuracy.

Simplified Elastic Design Method Using Equivalent Span Ratio for Two‐way Concrete Composite Slabs with Precast Ribbed Panels

Simplified Elastic Calculation Method of Precast Rectangular Rib Floor Concrete Two-way Composite Slab with One Edge Clamped and Three Edges Simply Supported

Shear Design Method for Non-Prismatic Concrete Beams Reinforced Using W-FRP

Simplified elastic calculation method of composite concrete two-way slab with simply supported edges under uniformly distributed loads

A Novel Approach for the Mechanical Response of Cement Concrete Pavement Structure Considering the Interlaminar Interface Shear Slip Effect

Practical elastic calculation methods of concrete two-way composite slab with precast ribbed panels

Simplified Design Method for the Shear Capacity of Steel Plate Shear-Strengthened Reinforced-Concrete Beams

Compressive Behavior and Design Calculations of CFST Slender Columns with Latticed Annular Steel Part

Design Sensitivity of Cross-tensioned BFRP Concrete Pavement

Calculating Method and Experimental Research on Lateral Load Distribution of Transversely Strengthened Hollow Slab Bridge

Experimental Study and Calculating Methods on Bending Rigidity of Precast Prestressed Concrete Ribbed Panels for Composite Slabs

Calculation of Long-Term Slippage for Externally Prestressing Steel-Concrete Composite Beam

INFLUENCE OF PREFORMED HOLES ON FLEXURAL DEFLECTION CALCULATION METHODS OF PRECAST PRESTRESSED CONCRETE RIBBED PANELS FOR COMPOSITE SLABS

Rigidity and Moment Distribution of Steel-Concrete Composite Waffle Floor Systems Considering the Spatial Effect

Ultimate Bearing Capacity of Concrete Two-way Composite Slabs with Precast Concrete Ribbed Panels

Long-Term Deflection of Prestressed Concrete Bridge Considering Nonuniform Shrinkage and Crack Propagation by Equivalent Load Approach

Stiffness amplification coefficient for composite frame beams considering slab spatial composite effect

Simplified Calculation Model and Finite-element Analysis of Frame-supported Ribbed-Grid Composite Slab Structure

Study on Calculation Method of Bending Performance of Concrete Sandwich Composite Slab

Simplified deflection calculation method for PC box girder bridges with corrugated steel webs using asynchronous-pouring-construction technology

Novel design method for reinforced concrete decks in composite girders considering compressive membrane action