Abstract:Indium tin oxide (ITO) nanofibers and ITO nanoparticles with enriched oxygen- defects were synthesized through facile electrospinning and sol-gel method. SnCl2, InCl3, and PVP (polyvinylpyrrolidone) were selected as precursors, while ethanolamine was employed as a hydrolysis controlling agent. The morphology, crystal structure, oxygen defects, and electrical performance of the ultrafine ITO nanofibers and nanoparticles were systematically characterized by transmission electron microscope (TEM), selection electron diffraction (SAED), scanning electron microscope (SEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), X-ray electron spectroscopy (XPS), and four point resistance tester. The ITO nanofibers were obtained by removal of the PVP matrix at 400 degrees C, and featured with ultrafine diameter, porous structure, and cubic phase. Furthermore, the resultant ITO nanofibers changed to oxygen. deficient nanoparticles with a high oxygen vacancy content of 38.9% at 800 degrees C The doping of Sn4+ ions into the In2O3 lattices leads to the expansion of the lattice and thus the increase of crystal plane spacing at elevated temperatures. When the temperature increased from 400 to 800 degrees C, the size of ITO nanoparticles grown from 32 to 44 nm. Meanwhile, the lattice strain (epsilon(0)) decreased from 1.943 x 10(-3) to 1.422 x 10(-3) and the strain-induced lattice relaxation decreased accordingly. No phase change from cubic structure to hexagonal structure was observed. Additionally, calcination at elevated temperature could hamper the (111) growth and thus cause the increase in the ratio of I-(400)/I-(222) in In2O3 that is proportional to the electrical conductivity of ITO. The maximized electrical conductivity of ITO nanoparticles was obtained upon a calcination temperature of 800 degrees C.

Microstructure, Grain Orientation, and Properties of ITO Ceramics Sintered with Various Heating Rates

Micro-structure of ITO Ceramics Sintered at Different Temperatures and Its Effect on the Properties of Deposited ITO Films

Effects of sintering processes on second-phase grain morphology of ITO ceramics and grain growth

Microstructure Evolution and Grain Orientation in ITO Targets and Their Effects on the Film Characteristics

The Influence of Sintering Temperature on the Porous Structure of ITO Materials

Effects of Element Chemical States and Grain Orientation Growth of ITO Targets on Photoelectric Properties of the Film

Influence of Annealing Temperature on the Microstructure and Electrical Properties of Indium Tin Oxide Thin Films

Effect of Different Thermo-Treatment at Relatively Low Temperatures on the Properties of Indium‑tin-Oxide Thin Films

Effects of Particle Size and Dispersion Methods of In2O3‐SnO2 Mixed Powders on the Sintering Properties of Indium Tin Oxide Ceramics

Sb2O3 doped and microwave assisted sintering of ITO

Effects of Sintering Processes on the Element Chemical States of In, Sn and O in ITO Targets

The key of ITO films with high transparency and conductivity: Grain size and surface chemical composition

Effects of Air Annealing on the Structure, Resistivity, Infrared Emissivity and Transmission of Indium Tin Oxide Films

Effect of Heat Treatment on the Dispersion and Sintering Behaviour of Tin Doped Indium Oxide Powders

Effect of Heating Rate on Ion Diffusion and Dielectric Properties of Ferroelectric-Dielectric Composite Ceramics

Correlation between microstructure and electrical, optical properties of thermal annealed ITO thin films

Fabrication Of Indium Tin Oxide Nanostructures By Electrospinning And Their Electrical Conductivity

Influence of sintering temperatures on structure and electrical conductivity of TiO2 cathode

Small Angle X-ray Scattering Studies on Structural Evolution During Calcination of Sol–gel ITO Nano-Powders

Effects of second-phase particles and elemental distributions of ITO targets on the properties of deposited ITO films

Effects of Cerium Oxide Doping on the Microstructure and Properties of ITO Targets and the Photoelectric Properties of the Films