Abstract:Steels with sub-micrometre grain sizes usually possess high toughness and strength, which makes them promising for lightweighting technologies and energy-saving strategies. So far, the industrial fabrication of ultrafine-grained (UFG) alloys, which generally relies on the manipulation of diffusional phase transformation, has been limited to steels with austenite-to-ferrite transformation<a href="#ref-CR1">1</a>,<a href="#ref-CR2">2</a>,<a href="/articles/s41586-021-03246-3#ref-CR3">3</a>. Moreover, the limited work hardening and uniform elongation of these UFG steels<a href="/articles/s41586-021-03246-3#ref-CR1">1</a>,<a href="/articles/s41586-021-03246-3#ref-CR4">4</a>,<a href="/articles/s41586-021-03246-3#ref-CR5">5</a> hinder their widespread application. Here we report the facile mass production of UFG structures in a typical Fe–22Mn–0.6C twinning-induced plasticity steel by minor Cu alloying and manipulation of the recrystallization process through the intragranular nanoprecipitation (within 30 seconds) of a coherent disordered Cu-rich phase. The rapid and copious nanoprecipitation not only prevents the growth of the freshly recrystallized sub-micrometre grains but also enhances the thermal stability of the obtained UFG structure through the Zener pinning mechanism<a href="/articles/s41586-021-03246-3#ref-CR6">6</a>. Moreover, owing to their full coherency and disordered nature, the precipitates exhibit weak interactions with dislocations under loading. This approach enables the preparation of a fully recrystallized UFG structure with a grain size of 800 ± 400 nanometres without the introduction of detrimental lattice defects such as brittle particles and segregated boundaries. Compared with the steel to which no Cu was added, the yield strength of the UFG structure was doubled to around 710 megapascals, with a uniform ductility of 45 per cent and a tensile strength of around 2,000 megapascals. This grain-refinement concept should be extendable to other alloy systems, and the manufacturing processes can be readily applied to existing industrial production lines.

Ultrafine Grained Dual-Phase Martensite/ferrite Steel Strengthened and Toughened by Lamella Structure

The synergistic effects of ultrafine grains and nano-size Cu-rich precipitates on the mechanical properties of DP steels

Towards ultra-high strength dual-phase steel with excellent damage tolerance: The effect of martensite volume fraction

Making low-alloyed steel strong and tough by designing a dual-phase layered structure

Microstructure, mechanical properties and strengthening mechanism of high strength hot-rolled ferrite-martensite dual phase steel

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

MICROSTRUCTURAL REFINEMENT OF STRUCTURAL STEELS

Achieving High Strength and High Ductility of Dual-Phase Steel Via Alternating Lamellar Microstructure

Microstructural and mechanical properties of ultra-high-strength dual-phase steel produced by ultra-fast cooling

Enhanced strength and ductility of the low-carbon steel with heterogeneous lamellar dual-phase structure produced by cyclic intercritical rolling

Ultrafine lamellar microstructure with greatly enhanced strength and ductility of martensite steel via heavily warm rolling of metastable austenite

Light-weight Isometric-Phase Steels with Superior Strength-Hardness-ductility Combination

Facile route to bulk ultrafine-grain steels for high strength and ductility

Simultaneous enhancement of strength and ductility in ferrite-martensite steel via increasing the martensite fraction

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

A novel technique for developing a dual-phase steel with a lower strength difference between ferrite and martensite

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Enhanced mechanical properties of a high-carbon martensite steel processed by heavy warm rolling and tempering

Toughening ultrastrong low-density steel by textured δ-ferrite lamellas

Research and development of a new hot rolled laminated structure

Achieving ultrahigh strength by tuning the hierarchical structure of low-carbon martensitic steel