Abstract:Among fuel cells, the direct methanol fuel cell (DMFC) has attracted great attention and has been considered a very promising power source because of the ease of methanol transportation and its high energy density. A major limiting factor hindering DMFC’s commercial application is the poor catalytic performance in the anode (methanol oxidation reaction). The methanol oxidation reaction (MOR) requires (OH-) from water dissociation as an oxygen donor for the reaction; however, the slow water dissociation on Pt limits the rate of MOR. In addition to the sluggish catalytic activity, the other major impediment for Pt catalysts is the generation of carbon monoxide (CO) during the MOR process.In order to improve the catalytic performance of MOR catalysts, a variety of catalyst design strategies have been devised. The interesting way of carrying out the MOR catalytic process is the non-CO pathway which takes place on Pt-Au bimetallic catalysts, thus eliminating CO poisoning. However, the overall activity of Pt-Au alloys in MOR is relatively low, which ultimately limits the application of Pt-Au catalysts. In this study, a nanoporous (np) Au-Cu-Pt thin-film catalyst with a fine structure and tunable composition is synthesized by using a facile method involving successive electrodeposition and de-alloying. SEM, SEM-EDX and ICP have been used for morphology characterization and composition assessment. Pb under-potential deposition (UPD), H UPD and CO stripping tests have been employed to determine the electrochemical active surface area (ECSA) and to probe the Pt active sites specifically. Also, cyclic voltammetry (CV) tests have been performed to assess the catalytic performance in MOR. Finally, long-term CV and chronoamperometry (constant potential) tests have been used to study and evaluate the durability of accordingly synthesized catalyst for MOR. The prepared np Au-Cu-(8% in the precursor alloy)Pt catalyst exhibits outstanding mass and specific activity toward the MOR, which is approximately six- and nine-times higher than the activity of a commercial Pt/C(40%) counterpart, respectively. A negative 75 mV onset potential shift upon the MOR anodic scan on the np Au-Cu-(8 %)Pt catalyst in comparison with Pt/C(40%) corroborates its higher catalytic activity. Furthermore, the alloy catalyst demonstrates better durability than the Pt/C(40%) counterpart in a three-hour constant potential test and exhibits full post-factum recovery of its cycling activity. In addition, it retains more than 60% of its original activity after 3000 cycles of an accelerated degradation test. Reference: Xie, Y., Li, C., Razek, S.A., Fang, J. and Dimitrov, N., 2020. Synthesis of Nanoporous Au− Cu− Pt Alloy as a Superior Catalyst for the Methanol Oxidation Reaction. ChemElectroChem, 7(2), pp.569-580.

Highly Catalytical Performance of Nanoporous Copper for Electro-Oxidation of Methanol in Alkaline Media

Highly Active Nanoporous Pt-based Alloy As Anode and Cathode Catalyst for Direct Methanol Fuel Cells

PdCu Alloy Nanodendrites with Tunable Composition As Highly Active Electrocatalysts for Methanol Oxidation

Facile Synthesis of Ptcu3 Alloy Hexapods and Hollow Nanoframes As Highly Active Electrocatalysts for Methanol Oxidation

SnNi Nanoneedles Assembled 3D Radial Nanostructure Loaded with SnNiPt Nanoparticles: Towards Enhanced Electrocatalysis Performance for Methanol Oxidation

Copper Vanadate Nanowires on G-C3n4 Toward Highly Selective Oxidation of Methanol to Dimethoxymethane

Nanoporous Nickel-Copper-phosphorus Amorphous Alloy Film for Methanol Electro-Oxidation in Alkaline Medium

Synthesis and application of Cu(OH)2 nanowires on nanoporous copper prepared by dealloying Ti50Cu50 and Ti25Zr25Cu50 amorphous alloys

Pd-on-NiCu Nanosheets with Enhanced Electro-Catalytic Performances for Methanol Oxidation

Pt Nanoparticles Dispersed on Ni/C Nanoflowers As Stable Electrocatalysts for Methanol Oxidation and Oxygen Reduction

Novel-Phase Structural High-Efficiency Anode Catalyst for Methanol Fuel Cells: Α-(Nicu)3pd Nanoalloy

Excellent electrocatalytic performance toward methanol oxidation of hierarchical porous NiCu obtained by electrochemical dealloying

Fabrication and Degradation Properties of Nanoporous Copper with Tunable Pores by Dealloying Amorphous Ti-Cu Alloys with Minor Co Addition

Electro-catalytic Performance of Pd Decorated Cu Nanowires Catalyst for the Methanol Oxidation

Nanoporous Au-Cu-Pt As a Superior Electro-Catalyst for the Methanol Oxidation Reaction

Au-doped PtCu 2 nanonetworks with interface-rich for enhancing methanol electro-oxidation performance

Nickel Foam Supported Mesoporous Nico2o4 Arrays With Excellent Methanol Electro-Oxidation Performance

Methanol Electro-Oxidation on Cu@Pt/C Core-Shell Catalyst Derived from Cu-MOF

Nanoporous Pdni Bimetallic Catalyst with Enhanced Electrocatalytic Performances for Electro-Oxidation and Oxygen Reduction Reactions

Electrocatalytic Performance for Methanol Oxidation on Nanoporous Pd/NiO Composites Prepared by One-Step Dealloying

Co Ion‐, NiS2‐ and CNT‐Co‐Doped Nanoflower/Hollow Spherical NiO Nanocomposites for Efficient Electrocatalytic Oxidation of Methanol