Abstract:Perovskite solar cells (PSCs) have been developed as a promising photovoltaic technology because of their excellent photovoltaic performance. However, interfacial recombination and charge carrier transport losses at the surface greatly limit the performance and stability of PSCs. In this work, the fabrication of high-quality PSCs based on methylammonium lead iodide with excellent ambient stability is reported. An anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), is introduced to simultaneously passivate the defect states and stabilize the cubic phase of the perovskite film. The SDBS located at grain boundaries and the surface of the active layer can effectively passivate under-coordinated lead ions and protect the perovskite components from water-induced degradation. As a result, a champion power conversion efficiency (PCE) of 19.42% is achieved with an open-circuit voltage (VOC) of 1.12 V, a short-circuit current (JSC) of 23.23 mA cm–2, and a fill factor (FF) of 74% in combination with superior moisture stability. The SDBS-passivated devices retain 80% of their initial average PCE after 2112 h of storage under ambient conditions.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c14732?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c14732</a>.Device fabrication, GIWAXS characterization, device characterization, contact angle measurements, spectroscopy data, SEM data, GIWAXS data, and XRD data (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c14732/suppl_file/am0c14732_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Dimethyl Sulfoxide Post-Treatment Inducing Defect Healing and Crystal Growth for Effective Perovskite Solar Cells

Dimethyl Sulfoxide and Bromide Methylamine Co-Treatment Inducing Defect Healing for Effective and Stable Perovskite Solar Cells

Remanent solvent management engineering of perovskite films for PEDOT: PSS-based inverted solar cells

Improved Crystallization of Perovskite Films by Optimized Solvent Annealing for High Efficiency Solar Cell.

Removal of Residual Additive Enabling Perfect Crystallization of Photovoltaic Perovskites

Aqueous solvent-regulated crystallization and interfacial modification in perovskite solar cells with enhanced stability and performance

Boosting the Film Quality by Simultaneously Pre‐wetting the PbI2 Film and Ostwald Ripening the MAPbI3 Film with DMSO Addition into MAI Solution

Dual Functions of Crystallization Control and Defect Passivation Enabled by Sulfonic Zwitterions for Stable and Efficient Perovskite Solar Cells.

Post-treatment techniques for high-performance perovskite solar cells

Methylamine-induced defect-healing and cationic substitution: a new method for low-defect perovskite thin films and solar cells

Unveiling a Key Intermediate in Solvent Vapor Postannealing to Enlarge Crystalline Domains of Organometal Halide Perovskite Films

Surface Reconstruction via Molten Chloride Salt for Efficient and Stable Perovskite Solar Cells

Sodium Dodecylbenzene Sulfonate Interface Modification of Methylammonium Lead Iodide for Surface Passivation of Perovskite Solar Cells

Solvent-Induced Textured Structure and Improved Crystallinity for High Performance Perovskite Solar Cells

Synergistic Effect of Guanidine Thiocyanate Additive and Dimethyl Sulfoxide Post-Treatment Towards Efficient and Stable Perovskite Solar Cell

Dissolution-recrystallization Method for High Efficiency Perovskite Solar Cells

Solvation‐Driven Grain Boundary Passivation Improving the Performance of Perovskite Solar Cells

Crystal Reconstruction and Defect Healing Enabled High-Quality Sb2Se3 Films for Solar Cell Applications

Promoting crystalline grain growth and healing pinholes by water vapor modulated post-annealing for enhancing the efficiency of planar perovskite solar cells

Homogenizing Morphology and Composition of Methylammonium‐Free Wide‐Bandgap Perovskite for Efficient and Stable Tandem Solar Cells

Manipulating the Crystallization of Perovskite via Metal‐Free DABCO‐NH4Cl3 Addition for High Efficiency Solar Cells