Abstract:High-pressure (HP) processing is considered as an alternative technique for thermal sterilization of high quality foods. Adiabatic compression during pressurization allows for quick increase in temperature of food products, which is reversed when the pressure is released, thereby providing rapid heating and cooling conditions and hence short process times. However, during the pressure holding time, the product experiences a temperature drop as a result of heat loss to the vessel. The temperature variation during the process and the synergistic effect of temperature and pressure make it difficult to get the required accurate data on microbial spore destruction kinetics. In this study, a polyoxymethylene (POM)-insulated chamber was evaluated for temperature control in the test sample during pressure treatment. Temperature variations in the HP system were measured in milk test samples inside the POM insulator and pressure medium in the HP vessel under various conditions of pressures (500–900 MPa) and initial temperatures (20–80 °C). Results demonstrated that the POM chamber had good thermal-insulation characteristics under pressure and was able to maintain stable operating conditions for microbial spore destruction kinetics. Based on the measured adiabatic temperature change, the required initial temperatures for the test sample and pressure medium were generated as a quadratic function of pressure and temperature. The setup was then verified for pressure inactivation of Clostridium sporogenes (PA 3679) spores in ultra-heat-treated milk. The better temperature stability of test samples during treatment provided a means to gather accurate data on HP destruction kinetics of the microbial spores.

Adiabatic compression heating of selected organic solvents under high pressure processing

Solubilities of N2, H2, Ar in 1-Octanol at High Pressure

Solubility and volumetric mass transfer coefficient of ethylene and propylene in n-hexane solution of low molecular weight polyethylene

Compression Heating and Temperature Control for High-Pressure Destruction of Bacterial Spores: An Experimental Method for Kinetics Evaluation

Excess Molar Enthalpies of Methyl Acetate and (1-Propanol, 2-Propanol, 1-Butanol, 2-Butanol, and 1-Pentanol) at T = (298.15 and 308.15) K and P = (5.0 and 10.0) MPa

Measurement of Critical Temperatures, Critical Pressures and Densities of Acetone–Water Solutions for Simulation

Molar excess enthalpies of ethyl acetate+alkanols at T=298.15K, p=10.0MPa

High pressure Raman spectroscopy investigation on acetonitrile and acetonitrile–water mixture

Excess Molar Enthalpies of Dimethyl Carbonate and (butanol Isomers and 1-Pentanol) at T = (298.15, 313.15, and 328.15) K and P = (0.1, 1.0, and 10.0) MPa

Direct-Contact Condensation of Hydrocarbon Mixtures in A Structured Packing Bed

The Laminar Burning Velocity of Propyl Acetate at High Pressures and Temperatures

Prediction of Solubility of Acetylene in Organic Solvents over a Wide Range of Temperature and Pressure

Solvent Effect in the Copolymerization of Ethylene and Vinyl Acetate

Experimental Investigation on the Solubility of Oxygen in Toluene and Acetic Acid

Excess Molar Enthalpies of N-Octanol N-Alkane and Isopentanol N-Dodecane Mixtures under High-Pressure

Molecular modeling of phase behavior and microstructure of acetone-chloroform-methanol binary mixtures

Solubility Determination, Thermodynamic Modeling, and Solvent Effect of 2′,4′-Dihydroxyacetophenone in 10 Monosolvents and Two Binary Solvents from 293.15 to 333.15 K

A molecular dynamics investigation on sub/supercritical phase change for alcohol/ n -heptane mixtures

Thermal conductivity measurements for n-hexane and n-heptane at elevated temperature and pressure

Experimental and kinetic modeling study of ethylene oxidation at elevated pressure

In Situ Visualization of Transformation of Organic Matter in Water at High Pressures and Temperatures