Abstract:In this work, novel turned-bearing extrusions (TBE) conducted by using the dies with the single corner and double corner, named SC-TBE and DC-TBE respectively, are developed to introduce additional shear strain during the preparation of AZ31 alloy sheets, which is expected to improve the strengths of sheets. Numerical simulations are conducted to uncover the effect of additional shear deformation on the microstructure during the TBE. The results show that the high strain during the TBE leads to a high nucleation rate for dynamic recrystallization (DRX), resulting in grain refinement of the extruded Mg alloy sheet. However, the high strain also increases the temperature of the material due to the heat generated by plastic deformation, which provides a great driving force for grain growth and consumes dislocations. As these two effects compete with each other when increasing the strain near the die orifice, the SC-TBE sheet has finer grains and a higher residual dislocation density compared to the DC-TBE sheet or the sheet prepared by the conventional extrusion (CE). Fine-grain strengthening and substructure strengthening work together and enhance the tensile yield strength (TYS) of the SC-TBE sheet. The TYSs along extrusion direction (ED), transverse direction (TD) and 45° direction (the half angle between ED and TD) of the SC-TBE sheet are improved by 32 MPa, 65 MPa and 35 MPa respectively compared with the CE sheet. The findings of this research provide some new insights into the development of new preparation methods for Mg alloy sheets with higher strength.

Improved Mechanical Properties of Mg-3Al-1Zn Alloy Sheets by Optimizing the Extrusion Die Angles: Microstructural and Texture Evolution

Effect of transverse gradient extrusion process on texture and mechanical properties of Mg–3Al–1Zn alloy sheets

Mechanical Properties Of Az31 Mg Alloy Extruded At Different Die Temperatures

Improving mechanical properties of AZ31 alloy sheets via novel turned-bearing extrusion by introducing shear strain

Study on the Microstructure and Properties of AZ31 Alloy by Hot Die Forging Extrusion

Microstructure Evolution and Mechanical Properties of AZ31 Magnesium Alloy Sheets Prepared by Low-Speed Extrusion with Different Temperature

Effects of Hot Rolling Processing on Microstructures and Mechanical Properties of Mg–3%Al–1%Zn Alloy Sheet

Microstructure and Mechanical Properties of Extruded Az31 Magnesium Alloy Sheet

Effect of grain size distribution and texture on the cold extrusion behavior and mechanical properties of AZ31 Mg alloy

Microstructure and Mechanical Properties of Mg–3Al–Zn Magnesium Alloy Sheet by Hot Shear Spinning

Microstructural characterization and mechanical behavior of Mg-AZ31B/Al 6063 bimetallic sheets produced by combining continuous shear deformation with direct extrusion

Microstructure Evolution and Hot Extrusion Behavior of AZ31-Nd Magnesium Alloy Adopting AZ31 Chips and Mg-Nd Chips

Effects of Extrusion Ratio on the Microstructure, Texture and Mechanical Properties of Mg-2.5Nd-0.5Zn-0.5Zr Alloy Sheets

Microstructure and Tensile Properties of AZ61 Alloy Sheets Processed by High-Ratio Extrusion with Subsequent Direct Aging Treatment

Grain Refinement and Orientation of AZ31B Magnesium Alloy in Hot Flow Forming under Different Thickness Reductions

Grain Refinement and Mechanical Properties of AZ31 Alloy Processed by Pre-die Forging Extrusion at Different Temperatures

Fabrication of Excellent Mechanical Properties AZ31 Magnesium Alloy Sheets by Conventional Rolling and Subsequent Annealing

Optimization of Microstructure and Mechanical Property of a Mg-Zn-Y-Nd Alloy by Extrusion Process

Microstructures and Mechanical Properties of Hot Rolled AZ31 Mg Alloy Sheets

Effects of extrusion ratio on the microstructure and mechanical properties of AZ31 Mg alloy

Effect of Extrusion Deformation on Microstructures and Properties of AZ31 Magnesium Alloy