Abstract:b Through the ring-opening polymerization of L-lactide initiated by hydroxyl groups on the surface of HNTs using stannous 2-ethylhexanoate as catalyst, halloysite nanotubes surface-grafted with poly (L-lactic acid) (PLLA) segments (g-HNTs) were synthesized. The compositions and morphologies of the modified and unmodified HNTs were observed by Fourier transformation infrared (FTIR), thermal gravimetric analysis (TGA) and transmission electron microscopy (TEM). Then, a series of PLLA, PLLA/HNTs and PLLA/g-HNTs nanofiber membranes were prepared by electrospinning, the influences of the spinning conditions on the morphologies of the nanofiber membranes were discussed, and the composition, micrograph, interfacial compatibility, tensile properties and cellular compatibility of the composite membranes were studied too. Results showed that the grafting percentage of PLLA segments on the surface of g-HNTs was 14.22% as the molar ratio of HNTs to L-lactide was 1:10. The tubular morphology of HNTs changed little after surface grafting, and g-HNTs can easily disperse in anhydrous ethanol. The voltage and the feed rate have effects on the morphology of fiber membranes, when the voltage was 15 kV and feed rate was 1 mL/h, the diameter of the electrospinning fiber was relatively uniform. The dispersion and interfacial compatibility of g-HNTs in PLLA matrix were superior to those of pristine HNTs, when the content of g-HNTs increased up to 40 wt%, the fiber micrograph of the PLLA/g-HNTs composite membranes continues to remain good, and continuous and relatively uniform fiber can be got. With the content of HNTs and g-HNTs increased, the tensile strength and modulus increased first and then decreased, as the filler content was 5 wt%, the highest tensile strengths and moduli were obtained for both of the PLLA/HNTs and PLLA/g-HNTs composite nanofiber membranes. However, the tensile strength and modulus of the PLLA/g-HNTs composite nanofiber membranes were always higher than those of PLLA/HNTs composite nanofiber membranes at all filler contents due to the good adhesive strength between the g-HNTs and PLLA matrix. The results of 3T3 cells culture in vitro indicated that the cellular compatibility of the PLLA/g-HNTs composite nanofiber membranes is very good, and better than that of pure PLLA and PLLA/HNTs nanofiber membranes.

Preparation of PLGA/MWCNT Composite Nanofibers by Airflow Bubble-Spinning and Their Characterization

Nanocomposites of Poly(vinylidene Fluoride) with Multiwalled Carbon Nanotubes

Fabrication of Highly Oriented Nanoporous Fibers Via Airflow Bubble-Spinning

Preparation and Properties of Multi-Walled Carbon Nanotubes/Poly-L-Lactide Composite Ultrafine Fibers

Preparation and Characterization of Poly(lactic acid) Micro- and Nanofibers Fabricated by Centrifugal Spinning

Thermoplastic polyurethane/silica nanocomposite fibers by electrospinning

Preparation of MWCNTs/PAN Composite Microspheres by Aqueous Deposition Polymerization and Their Electrospun Fibers

Preparation and Characterization of Magnetic Multi-Walled Carbon Nanotubes–poly(l-Lactide) Composite

Effects of Electrospinning Parameters on Morphology and Diameter of Electrospun Plga/Mwnts Fibers and Cytocompatibility in Vitro

Preparation and Characterization of Poly(lactic acid)/nano-calcium Phosphate Composite Nanofibers by Electrospinning

Effect of Spinning Conditions on the Mechanical Properties of Pa6/Mwnts Nanofiber Filaments

Study on the preparation and properties of aligned carbon nanotubes/polylactide composite fibers

Fabrication and Characterization of Carbon Nanofibers with a Multiple Tubular Porous Structure Via Electrospinning

Morphology, Rheology and Crystallization Behavior of Polylactide Composites Prepared Through Addition of Five-Armed Star Polylactide Grafted Multiwalled Carbon Nanotubes

Preparation of PLLA/g-HNTs Composite Nanofiber Membranes by Electrospinning and Studies on Their Properties

Preparation and properties of composite phase-change nanofiber membrane by improved bubble electrospinning

Fabrication of PLA Nanoporous Fibers by DMF/CF Mixed Solvent via Electrospinning

Preparation of carboxymethyl chitosan nanofibers through electrospinning the ball-milled nanopowders with poly (lactic acid) and the blood compatibility of the electrospun NCMC/PLA mats

ELECTROSPINNING OF POLY( LACTIDE- Co-Glycolide)/β-tricalcium PHOSPHATE COMPOSITES

The Study of Poly (L-Lactide) Grafted Silica Nanoparticles on the Film Blowing of Poly (L-Lactide)

Fabrication of high-density polyethylene/multiwalled carbon nanotube composites via submerged friction stir processing