Abstract:Dimethyl ether (DME) is a highly reactive diesel substitute that can be used as a pilot fuel to ignite low- reactivity methane (CH4) in heavy-duty engines. To optimize the efficiency and emissions of CH4/DME dual-fuel engines, it is crucial to study the fundamental combustion characteristics of DME mixed with methane. This study focuses on the influence of CH4 addition on the low-temperature oxidation (LTO) preparation stage and the thermal ignition (TI) preparation stage of DME in the two-stage ignition process, as these two stages respectively control the ignition delay of the first and second stages. The comparison is made between pure DME and a 50% CH4 and 50% DME blended fuel, operating under thermodynamic conditions representing the engine in- cylinder environment at 30 atm pressure, 650K temperature, and a stoichiometric equivalence ratio. The results show that the addition of methane hardly affects the control mechanism of the two-stage ignition of DME. Specifically, the LTO preparation stage is still promoted by the increase in OH radicals in the DME’s low-temperature oxygenation pathways to form KET, and the second stage is still controlled by the H2O2 loop mechanism. The kinetic analysis also reveals that methane addition can compete for some of the OH radicals in the LTO preparation stage, which has a suppressing effect on ignition. However, in the TI preparation stage, methane can promote the loop reaction of OH→HO2→H2O2→OH and promote ignition. For the operating conditions studied here, although methane consumes a total of 7.24% prior to thermal ignition, it only consumes 0.63% of the total amount in the LTO preparation stage and 1.81% of the total amount in the TI preparation stage. This indicates that methane is mainly consumed in the LTO stage, accounting for 65% of the total methane consumption amount. It can be concluded that the kinetic effect of methane has a relatively small impact on the ignition delay of the DME, at least for the conditions investigated here. In other words, the dilution and thermal effects caused by adding methane are the main reasons for the prolonged time of LTO/TI preparation. Overall, more fundamental research is warranted to understand the role of methane in the two-stage ignition process of DME, which could facilitate the development of CH4/DME dual-fuel engines.

Experimental Investigations on Combustion Acceleration Behavior of Methane/gasoline under Partial Load Conditions of SI Engines

Numerical Investigation of Methane Number and Wobbe Index Effects in Lean-Burn Natural Gas Spark-Ignition Combustion

Optical and Numerical Investigations of Flame Propagation in a Heavy Duty Spark Ignited Natural Gas Engine

Effect of Spark Timing on the Combustion Stages Seen in a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

An Experimental Investigation of Early Flame Development in an Optical Spark Ignition Engine Fueled with Natural Gas

Two-Stage Lean-Burn Combustion Inside a Natural-Gas Spark-Ignition Engine with a Bowl-in-Piston Chamber

An Experimental Study of the Combustion Process in a Natural-Gas Spark-Ignition Engine

Investigation of Multistage Combustion Inside a Heavy-Duty Natural-Gas Spark-Ignition Engine Using Three-Dimensional Computational Fluid Dynamics Simulations and the Wiebe-Function Combustion Model

The Effect of Methane Addition on the Low-Temperature Oxidation Preparation and the Thermal Ignition Preparation of Dimethyl Ether under Representative Engine In-Cylinder Thermal Conditions

Investigations on combustion system optimization of a heavy-duty natural gas engine

Experimental Investigation on the Effects of Direct Injection Timing on the Combustion, Performance and Emission Characteristics of Methanol/Gasoline Dual-Fuel Spark Turbocharged Ignition (DFSI) Engine with Different Injection Pressures under High Load

Experimental Research of High-Pressure Methane Pulse Jet and Premixed Ignition Combustion Performance of a Direct Injection Injector

Simulation and Research of Methane Premixed Combustion Characteristics Based on Constant Volume Combustion Chamber with Different Ignition Modes

Optical Study on the Effects of Methane Equivalence Ratio and Diesel Injection Mass on Diesel-Ignited Methane Combustion Process

Simulation Study on the Impact of Injection Strategies on the Performance of Methanol–Gasoline Dual-Fuel Engines

The Effects of Partially Premixed Combustion Mode on the Performance and Emissions of a Direct Injection Natural Gas Engine

Combustion Characteristics of a Direct-Injection Engine Fueled with Natural Gas−Hydrogen Mixtures

A numerical investigation on the effects of gaseous fuel composition in a pilot ignited direct injection natural gas engine

Experimental study on the effect of water port injection on the combustion and emission characteristics of diesel/methane dual-fuel engines

Combustion Process and Emissions of A Heavy-Duty Engine Fueled with Directly Injected Natural Gas and Pilot Diesel

Performance, combustion and knock assessment of a high compression ratio and lean-burn heavy-duty spark-ignition engine fuelled with n-butane and liquefied methane gas blend