Abstract:The ever increasing demand for safe and lightweight steel has promoted the development of advanced high-strength steel (AHSS). Recently, many AHSSs have been developed through chemical heterogeneity, resulting in microstructure refinement and mechanical property optimization. Although many efforts emphasize the construction of Mn-heterogeneous high-temperature austenite (gamma-Fe), the influence of Mn-heterogeneous distribution remains unclear. In this work, different austenitization times and temperatures are applied to Mn-partitioned pearlite, followed by the same quenching and partitioning process. The effect of Mn distribution in high-temperature austenite on the microstructural evolution and mechanical properties is systematically investigated. Results show that the Mn-heterogeneous high-temperature austenite can tailor the austenite-to-martensite transformation during quenching. The Mndepleted austenite is then readily transformed into lath martensite, and the Mn-enriched austenite is mainly retained as film roughness (RA), both of which assemble the ghost pearlite. With an increase in austenitization time and temperature, the Mn atom diffusion from the Mn-enriched austenite (originated from cementite lamellae) to the Mn-depleted one (originated from ferrite lamellae) increases, leading to the decreased chemical heterogeneity in high-temperature austenite. Thus, the fraction of ghost pearlite decreases while the fraction and size of blocky RA and coarse lath martensite increase. A wider lath martensite lowers the strength of the yield or the elastic limit of steel. The increased fraction and size of blocky RA ensure an increased uniform elongation by transformation-induced plasticity effect, whereas the transformation product (i. e., fresh martensite) is detrimental to the post-uniform elongation. Meanwhile, because the fractions of RA and martensite hardly change with austenitization condition, the ultimate tensile strength (about 1700 MPa) and total elongation (about 20%) are relatively constant. Therefore, tuning the Mn distribution in high-temperature austenite provides an effective strategy to tailor yield strength and uniform elongation while maintaining large ultimate tensile strength and total elongation.

Effect of Si and Mn Contents on the Microstructure and Mechanical Properties of Ultra-High Strength Press Hardening Steel

Effect of hot stamping and quenching & partitioning process on microstructure and mechanical properties of ultra-high strength steel

Enhanced Strength and Ductility of 2.4 GPa Hot‐Stamped Steel with an Extremely Thin Oxide Layer

Effect of Si Content on Microstructure and Properties of Low-Carbon Medium-Manganese Steel after Intercritical Heat Treatment

Microstructure Characterization and Tensile Properties of Hot Isostatic Pressed China Ultrahigh Strength Steel

Superhigh strength and ductile press-hardening steel produced by shortened austenitization of microstructure containing Mn/Cr-rich cementite particles

Microstructure and Performance Evaluations on Q&P Hot Stamping Parts of Several UHSS Sheet Metals

Microtructure and properties of 0.17C-1.83Mn-1.58Si steel and plasticity enhancement mechanisms of C, Mn partitioning

Microstructure and mechanical properties of Si-modified hot stamping steels treated by Q&P process

STUDY OF Mn AND P SOLUTE DISTRIBUTIONS AND THEIR EFFECT ON THE TENSILE BEHAVIOR IN ULTRA LOW CARBON BAKE HARDENING STEELS

Achieving Fine-Grained Microstructure and Superior Mechanical Property in a Plain Low-Carbon Steel Using Heavy Cold Rolling Combined with Short-Time Heat Treatment

Microstructure and Mechanical Properties of Ultra-high Strength Q&P Steel with 3.5% Mn

Effect of Mn content and strain rate on mechanical properties of high-C high-Mn austenitic steel

Effect of Alloy Elements Partitioning Behavior on Retained Austenite and Mechanical Property in Low Carbon High Strength Steel

Effect of C and Mn element partitioning behavior on microstructure and properties of cold-rolled medium manganese TRIP steel

Research on microstructure and mechanical properties of high strength steels BR1500HS during hot stamping

Influence of Oxygen Content on the Microstructure and Mechanical Properties of Hot Isostatically Pressed 30CrMnSiNi2A Ultra-High Strength Steel

Effect of Mn Heterogeneous Distribution on Microstructures and Mechanical Properties of Quenching and Partitioning Steels

Microstructure and mechanical properties of low carbon Mn-Si steel by different processes

Precipitation Behaviour and Strengthening Mechanisms of V-bearing 1800 MPa Grade Hot-Stamping Steel

Enhancement of strength-ductility trade-off in a 2000 MPa grade press-hardened steel via refined martensite with stable high-density cementite