Abstract:The performance of photovoltaic (PV) systems is known to degrade with temperature increase. To mitigate this issue, Phase Change Materials (PCMs) are utilized to regulate the temperature of PV modules. Many researchers have addressed the utilization of PCMs for thermal regulation of building integrated PVs (BIPV-PCM systems). Potential of integrating PV-PCM systems into membrane structures is relatively unexplored, it represents the novelty of this study. This paper explores the potential advantages and challenges of the thermal performance of OPV-ETFE foils with and without PCM integration under varying conditions. A detailed parametric analysis has been carried out to assess the impacts of ambient conditions and PCM properties under standard testing conditions. The results of this investigation offer critical insights into the thermal dynamics of OPV-PCM-ETFE modules and their application in building environments. A range of PCMs is analyzed and notably, Rubitherm-28 outperformed them, offering a 20-minute delay in temperature rise, showcasing its efficacy in thermal regulation for the OPV-PCM-ETFE module. Additionally, results indicate that an increase of 100 W/m 2 in solar radiation or 5 °C in ambient temperature consequently raised the OPV surface temperature by 5 °C. PCM thickness emerged as a critical factor for this integration. Each millimeter of PCM thickness adds approximately a 2-minute delay to the melt duration but owing to the low thermal conductivity property of both ETFE and PCMs, larger thickness can cause overheating issue. Therefore, it is recommended to use PCMs with higher latent heat capacity and melting points at least 10 °C above ambient temperature. The multi-parametric analysis further validated the flexibility of this approach across various conditions. An adaptive control strategy, informed by these findings, demonstrated potential for enhancing thermal management in OPV-PCM-ETFE modules using different control criteria. The adaptive control strategies help to optimize the thermal performance of the system and mitigate any potential overheating issues.

Electrical-thermal-mechanical Properties of Multifunctional OPV-ETFE Foils for Large-Span Transparent Membrane Buildings

OPV-PCM-ETFE Foils in Use for Public Buildings: Electrical Performance and Thermal Characteristics

Mechanical properties analysis of architectural PVDF/PES fabrics with uni-tensile and bi-axial test

ETFE Air Cushion Membrane Configurations,Structural Performances and Material Properties Experiments

Experiments on the mechanical properties and the welded seam properties of architectural membranes

Test on mechanical and electrical behavior of composite of flexible thin-film solar cells and PVDF membrane

Experimental Analysis on Electric-Thermal-Mechanical Behaviors of Composites of Flexible Thin Film Solar Cells and ETFE foils

Mechanical and Electrical Parameters Test for Flexible Thin-Film Solar Cell

Buildings with ETFE Foils: A Review on Material Properties, Architectural Performance and Structural Behavior

Thermal performance of ethylene tetrafluoroethylene foils integrated organic photovoltaics and phase change materials for building envelopes: A numerical study

Two-layer ETFE Cushions Integrated Flexible Photovoltaics: Prototype Development and Thermal Performance Assessment

Structural Behavior of the PV–ETFE Cushion Roof

Design of a Rigid Scaffold Structure Toward Efficient and Stable Organic Photovoltaics

Photothermal-structural-fluid Behaviors of PV-ETFE Cushion Roof in Summer: Numerical Analysis Using Three-Dimensional Multiphysics Model

Dynamic Mechanical Analysis of Ethylene Tetrafluoroethylene (ETFE) Foils in Use for Transparent Membrane Buildings

Rate-dependent mechanical properties and elastic modulus of ETFE foils used in inflated forming of transparency air-inflated cushion membrane structures

Thermal Performances of ETFE Cushion Roof Integrated Amorphous Silicon Photovoltaic

Temperature-stress-time Methodology for Flat-Patterning ETFE Cushions in Use for Large-Span Building Structures

Heat-Insulating Multifunctional Semitransparent Polymer Solar Cells

Modeling‐Guided Design of Semitransparent Organic Photovoltaics with Improved Energy Harvesting and Saving Capabilities

Experimental Study and Constitutive Modeling on Viscoelastic-Plastic Mechanical Properties of ETFE Foils Subjected to Uniaxial Monotonic Tension at Various Strain Rates