Record High-Power Narrow-Linewidth Fiber Laser Based on One-Stage Master Oscillator Power Amplification Configuration
Xi Xiaoming,Wang Meng,Tian Xin,Zhao Xiaofan,Rao Binyu,Wang Peng,Yang Baolai,Zhang Hanwei,Wang Xiaolin,Wang Zefeng,Chen Jinbao
DOI: https://doi.org/10.3788/cjl202249.1115001
2022-01-01
Chinese Journal of Lasers
Abstract:Objective The power scaling of high-power narrow-linewidth fiber lasers has recently received a lot of attention. It is challenging for power scaling in a narrow-linewidth fiber laser since thresholds of nonlinear effects, such as self-phase modulation (SPM) , stimulated Raman scattering (SRS) , stimulated Brillouin scattering (SBS) and transverse mode instability (TMI) , are much lower than those in a conventional fiber laser. A narrow-linewidth seed could be boosted using a master oscillator power amplification (MOPA) . Two promising seed sources, i.e. , phase-modulated single-frequency laser and fiber Bragg grating-based oscillator, are used in the narrow linewidth MOPA, and 3 kW and 5 kW level narrow-linewidth fiber lasers have been reported experimentally based on them, respectively. MOPAs based on the first type of seeds exhibit relatively weaker nonlinear effects and induce smaller spectrum broadening. However, the multistage configuration limits their applications. MOPAs based on the second kind of seeds (i. e. , one-stage MOPA) possess a simple and robust structure. Based on experimental and theoretical results, using onestage MOPA is a promising method for producing high power narrow-linewidth fiber lasers . Methods The one-stage MOPA system comprises a narrow-linewidth fiber oscillator and bidirectional pumped amplifier. A pair of homemade fiber Bragg gratings (FBGs) and a piece of Yb-doped fiber ( YDF) with a core/cladding diameter of 10/130 mu m were used to establish the seeds. High reflector (HR) and the output coupler ( OC) FBGs are 1.0 and 0.06 nm, respectively. The measured 3 dB bandwidth of the seed is similar to 0.05 nm at the output power of 20 W. A large-mode-area (LMA) YDF with a mode-filed area of similar to 420 mu m(2) was used in the amplifier. The seed laser was coupled into the amplifier using a mode-field adapter (MFA) to mitigate the mode-filed mismatching between them. Groups of wavelength-optimized LDs were spliced with the forward and backward combiners and used as pump sources. The unabsorbed cladding light was stripped off using a cladding light stripper. Then the output power, optical spectrum, and beam quality of the laser were measured using a characterization setup. Results and Discussions A maximum output power of 6.02 kW was achieved at a pump power of 7.0 kW, with the corresponding optical-to-optical efficiency of 85.7%. An evident spectral wing broadening can be observed with the increase of the output power [Figs. 2(b) and (c) ] . However, the 3 dB and 10 dB bandwidths of the spectrum increase relatively slow. At the maximum power, the measured 3 dB and 10 dB linewidths of the laser are 0.36 and 1.47 nm, respectively. The Raman suppression ratio is similar to 27 dB. Because of the large core size of the fiber, the output laser operates in a multimode regime and measured M-2 is similar to 2.7 at the maximum power. Conclusions This paper demonstrated a 6.02 kW narrow-linewidth fiber laser based on a one-stage MOPA fiber laser system. At the maximum power, the 3 dB and 10 dB linewidths are 0.36 and 1.47 nm, respectively. The peak signal-to-noise ratio is similar to 27 dB compared with the Raman Stokes light. The beam quality ( M-2 factor) is similar to 2.7. To the best of our knowledge, this is the highest power of narrow-linewidth fiber lasers that have ever been reported. In the following work, we will continue to optimize the temporal properties of the seed and the structure of the amplifier to further improve the output power and beam quality of the laser.