Abstract:This study successfully prepared crack-free WC10%-Ni60AA cermet coatings with high hardness using directed-energy deposition incorporating substrate preheating up to 500 °C. At the bottom of the deposit, the crack-free coating microstructure exhibited a lamination layer with a coarse herringbone eutectic, and the crystal-microstructure phase mainly comprised γ-Ni solid solution and eutectic precipitation Ni 17 W 3 , Ni 31 Si 12 , and Cr 23 C 6 . At the middle and top of the deposit, the microstructure exhibited a dense net-like eutectic, including a dendritic with the main phase of γ-Ni solid solution, interdendritic with a main phase of Cr 23 C 6 , and subdendritic with a main phase of Ni 31 Si 12 , Ni 17 W 3 , and a small block-like precipitate with a main phase of Cr 2.4 W 0.6 Si. Furthermore, the deposits on the substrate preheated to 500 °C exhibited the highest hardness (812 HV, an increase of 64 % compared to that of the non-preheating sample) owing to the dense net-like eutectic precipitation with fine-grain structure. Furthermore, wear test results show that the wearing process is divided into three stages: the rapid-increase stage; the plowing-friction stage; and the stable-wear stage. Specifically, as the load increased from 100 N to 400 N, the width and depth of the wear tracks increased, and the wear mechanisms were adhesive and oxidation, with the most severe wear occurring under a load of 400 N. Similarly, as the speed increased from 50 RPM to 300 RPM, the width and depth of the wear tracks increased, and the wear mechanisms were adhesive and oxidation at low speeds. When the speed was increased to 300 RPM, the most severe wear occurred, and the wear mechanisms were primarily adhesive and abrasive, along with a small amount of oxidation wear.

Preparation and Property Characterization of WS 2 Coatings Deposited on Micro-Nano Textured Surfaces of Cemented Carbide at Different WS 2 Target Currents

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Influence of Surface Morphology and Microstructure on Performance of CVD Tungsten Coating under Fusion Transient Thermal Loads

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Microstructures and Properties of Novel Nanocomposite WNx Coatings Deposited by Reactive Magnetron Sputtering

Microstructure and wear resistance of bimodal cemented carbide coating prepared by direct laser powder deposition

Molecular Dynamics Simulation Study on the Friction Performance of WS2 Coated Copper During the Scratching Process

Preparation and Tribological Properties of WS2 Solid Lubricating Coating with Dense Structure Using HiPIMS

Investigation of indentation response, scratch resistance, and wear behavior of tungsten carbide coatings fabricated by two-step interstitial carburization on tungsten

Comparative Study of Mechanical Performance of AlCrSiN Coating Deposited on WC-Co and cBN Hard Substrates

Nano-crystallization-Driven High Temperature Self-lubricating Properties of Magnetron-Sputtered WS2 Coatings

Influence of Substrate Hardness Transition on Built-Up of Nanostructured WC–12Co by Cold Spraying

Microstructure and wear behaviors of a WC10%-Ni60AA cermet coating synthesized by laser-directed energy deposition

Characterization of Nano-Structured WC-Co Deposited by Cold Spraying

Microstructure, Mechanical and Tribological Properties of WC-WCoB Coating

Microstructure and Formation Mechanism of WC Coating on Tungsten Fabricated by Interstitial Carburization: A Multiscale Investigation

Surface Topography of CVD-W Coatings on Graphite Substrate with a PVD-Si Intermediate Layer after Thermal Fatigue Testing

Effect of Particle and Carbide Grain Sizes on a HVOAF WC-Co-Cr Coating for the Future Application on Internal Surfaces: Microstructure and Wear

Investigation of Novel Nano-carbide WC/CoCr Coatings Applied by HVAF

Effects of Cu and WS2 addition on microstructural evolution and tribological properties of self-lubricating anti-wear coatings prepared by laser cladding