Abstract:Flexoelectric material under certain inhomogeneous electric field can be utilized to control the vibration of flexible structure based on the converse flexoelectric effect. The atomic force microscope (AFM) probe placed on the top of flexoelectric patch and the electrode under it with certain voltage applied between them are used to generate the inhomogeneous electric field. The actuation membrane force and bending moment induced by flexoelectric patch in turn influence the vibration of shells. In this study, an elastic cantilever beam excited by an initial static mechanical force locating at the tip end is considered. As the mechanical force withdraws the snapback response appears where the cantilever beam vibrates with all mode participating and their amplitudes decaying exponentially. Multiple actuators, consist of AFM probes and flexoelectric patches, are used here to accelerate the decrease of snapback response. On each probe voltages of multiple frequencies are applied to obtain the control effects on multiple modes. The actuator’s positions minimizing the tip displacement of the beam is selected as the optimal ones. Two way of determining the control voltage, i.e., open loop and close loop, is introduced and the information of positions of the actuators are emphasized in both methods. In case studies, the free damping vibration of the beam without control is evaluated and the first mode dominates the vibration. The open loop method, with constant amplitude of control voltage, doesn’t work well in a relatively long time scale. While the close loop method, with its control voltage related to the tip displacement detected by a sensor, turns out to be more stable and effective. The optimal positions for the actuations of both methods are clustered near the fixed end, where the actuation factor reaches its maximal value. At last, limitation on voltage amplitude is implemented to avoid the stress concentration, under which the control effect does not weaken much. This study serves as an introduction to flexoelectric material & multiple AFM probe based vibration control and a theoretical foundation for further researches.

An Electrostatic Actuator With Variable Stiffness For Suppression Of Rebound Due To Waveform Deviations

AN ELECTROSTATIC ACTUATOR WITH INHERENT VARIABLE STIFFNESS TO SUPPRESS BOUNCE WITH ROBUSTNESS AGAINST GAP VARIATIONS

A Self-Adaptive Stiffness Approach to Improving the Robustness of Electrostatic Switches Against Parameter Variations

A Variable Stiffness Strategy for Improving Comprehensive Performances of Micromachined Electrostatic Switches

Multi-physics Analysis of an Electrostatically Actuated Microcantilever in Viscous Fluids

A Nonlinear Electrostatic Actuator With Near Zero Impact Velocity, Low Driving Voltage And Large Stable Travel

An Inherent Nonlinear Electrostatic Actuator Without Any Additional Auxiliary to Reduce Pull-in Voltage and Extend Travel Range

Control of Beam’s Snapback Responses Using Multiple Flexoelectric Actuators

A Novel Inertial Microswitch with Synchronous Follow-Up Compliant Electrodes for Extending Output Switch-on Pulse Width

Active Damping of Ultrafast Mechanical Switches for Hybrid AC and DC Circuit Breakers

Electroactive soft bistable actuator with adjustable energy barrier and stiffness

A Restoring Force Boosting Structure with Flexible Stiction Recovery Electrode for MEMS Relays/Switches

A Heterogeneous Integrated MEMS Inertial Switch with Compliant Cantilevers Fixed Electrode and Electrostatic Locking to Realize Stable On-State

Design, Modeling, and Control of a Compact and Reconfigurable Variable Stiffness Actuator Using Disc Spring

Inertial Micro-Switch Capable of Prolonging Contact Time

Design and Characterization of an Inertial Microswitch with Synchronous Follow-Up Flexible Compliant Electrodes Capable of Extending Contact Duration

Automated and Optimal Actuation Voltage Waveform Design for Contact Bouncing Mitigation of Mems Switches

Analysis and elimination of the ‘skip contact’ phenomenon in an inertial micro-switch for prolonging its contact time

Micro-cantilever Shocking-Acceleration Switches with Threshold Adjusting and ‘On’-State Latching Functions

Strong Reliable Electrostatic Actuation Based on Self-Clearing Using a Thin Conductive Layer

Modeling, Simulation and Characterization of a Micromachined Acceleration Switch with Anti-Stiction Raised Strips on the Substrate