Abstract:Nowadays, the flow field at the compressor is more and more complex with the increasing of the aerodynamic loading. The complex flow in the endwall regions is thus key to aerodynamic blockage, loss production, and finally its performance deterioration. The design of Blended Blade and End Wall (BBEW) contouring technology had been proved to be useful in delaying, reducing, and eliminating the corner separation in the compressor. The BBEW technology can adjust the dihedral angle between the suction and the endwall in 30% of the spanwise easily, which is different with the fillet. However, the design of the BBEW always relies on the experiences of the designers, and the effective design results cannot be the optimal result. This paper presents an optimization design method for the BBEW technology, and analyses the flow mechanism of the BBEW design. Firstly, the parameters for the BBEW design is simplified as two, one is the maximum blended width, the other is the axial position of the maximum blended width. The optimal result can be obtained through the response surface method. Secondly, based on the optimization method, this paper make an optimization BBEW design at the suction side of a NACA65 linear compressor cascade with the turning angle 42 degrees. The numerical results show that the optimal BBEW design can eliminate the boundary layer separation at the corner intersection region, and reduce the suction side separation. When the incidence angle is 0 degrees, the BBEW technology can reduce the total pressure loss coefficient by 5%, and reduce the aerodynamic blockage coefficient by 14%. The aerodynamic performance of the cascade shows a more obvious improvement with the BBEW design at a larger incidence. The total pressure loss coefficient of the cascade is reduced by 20% at 15 degrees incidence. The numerical study shows that the design with the BBEW can control the axial development of the dihedral angle between the suction side and the endwall, which can eliminate the boundary layer separation at the corner intersection region. What’s more, the BBEW technology can produce a pressure gradient at the axial position of the maximum blended width, and value of the pressure gradient in proportion to the maximum blended width. This pressure gradient enhance the kinetic energy of the low energy fluid at the endwall region, which is consist of the secondary cross flow, thus elevating the capability to withstand the adverse pressure gradient, and improve the suction side separation around the trailing edge.

Correlation of Solidity, Aspect Ratio and Compound Lean Blade in Compressor Cascade Design

Flow Reconstructions and Aerodynamic Shape Optimization of Turbomachinery Blades by POD-based Hybrid Models

Optimization Design of Aspect Ratio and Solidity of a Heavy-Duty Gas Turbine Transonic Compressor Rotor

Performance Sensitivity Analysis and Aerodynamic Optimization of Compressor Cascades by a Turbulence Adjoint Method

Secondary Flow Reduction By Blade Redesign And Endwall Contouring Using An Adjoint Optimization Method

Implementation of Flow Loss Minimization Incorporating the Riblet Technique on Cascade Profile and Experimental Validation

Experiment and Numerical Simulation of the Performance on Scaled Compressor Cascade and Development of a Prediction Model

Performance Characteristic Modeling for 2D Compressor Cascades

Design Optimization of the Last Stage of a 4.5-Stage Compressor Using a POD-based Hybrid Model

Design Optimization of a Blended Blade and Endwall in a Compressor Cascade

Bleed air CFD modelling in aerodynamic simulation of A heavy duty gas turbine compressor

Design criteria of load split and chord length ratio for highly loaded compressor tandem cascades

The Use of Blended Blade and End Wall in Compressor Cascade: Optimization Design and Flow Mechanism

Aerodynamic Design Method and Experimental Investigation of a High-Load Supersonic Compressor Cascade

Shapley Additive Explanations of Multigeometrical Variable Coupling Effect in Transonic Compressor

Maximum Thickness Location Selection of High Subsonic Axial Compressor Airfoils and Its Effect on Aerodynamic Performance

Numerical Simulation of Effect of Blade End Slot on Performance of Compressor Cascade

Multi-Objective Optimization of Cascade Blade Profile Based on Reinforcement Learning

Three-Dimensional Compressor Blading Design Improvements in Low-Speed Model Testing

Optimal Design and Analysis of a High-Load Supersonic Compressor Based on a Surrogate Model

Interaction mechanism between the tip leakage flow and inlet boundary layer in a highly loaded compressor cascade based on scale-adaptive simulation