Abstract:Nowadays the phase controlled switching is a preferred method for capacitive switching. Thus the prestrike characteristic is an important issue for the control strategy. The objective of this paper is to understand the prestrike characteristics of vacuum interrupters (VIs) in the capacitive making operations of 40.5 kV vacuum circuit breakers (VCBs). In the experiment, three VIs with CuCr50 (50 wt% of Cr) contact material and three VIs with CuCr40 (40 wt% of Cr) contact material with contact diameter of 50 millimeters were prepared. The CuCr50 and CuCr40 contact materials are made by using infiltration and arc-melted technology, respectively. An L-C oscillating circuit generated an inrush current with a frequency of 207 Hz and with a peak of 6.48 kA, while the applied voltage was 46.3 kV which is equivalent to the peak voltage for a 35 kV three-phase network whose capacitive voltage factor is 1.4. The experimental results show that the complementary cumulative distribution function (CCDF) of the prestrike gaps d(pre) follows a 3-parameter Weibull distribution. The prestrike gap below which prestrike would always occur is similar for all six test VIs which is 2.4-3.1 mm. However, the average values of d(10), d(50) and d(90) for infiltration CuCr50 contact material are 57.5%, 45.3% and 28.9% higher than the ones in arc-melted CuCr40 contact material, respectively. During the inrush current flowing, at each zero-crossing of the inrush current the prestrike arc tries to extinguish with the occurrence of three types of contact gap breakdowns. Furthermore, if the contact gap breakdowns are withstood at the inrush current zero-crossing, inrush current interruption phenomenon happens, which proves a common phenomenon in capacitive making operation. The inrush current interruption phenomenon is mainly determined by the prestrike distance and not by the material quality. The experimental results imply that the field emission dominated breakdown and the micro-particle induced breakdown both take effect in the prestriking and contact gap breakdown process.

Fractal Features Of Contact Surface Ruptured From Arc Welding By High Frequency Inrush Current In Vacuum Interrupters

Relationship Between Morphology Feature of Contact Surfaces and Impulse Breakdown Voltage in Vacuum Gap under a Non-uniform Electric Field

Prestrike Characteristics Of Arc-Melted Cucr40 And Infiltration Cucr50 Contact Materials In 40.5 Kv Vacuum Interrupters Under Capacitive Making Operations

Deformation of contact surfaces in a vacuum interrupter after high-current interruptions

Inrush current prestriking arc behaviors of vacuum interrupters under CuCr50/50 and CuW10/90 contact materials

Inrush Current Prestrike Arc Behaviours Of Contact Materials Cucr50/50 And Cuw10/90

Investigation of Vacuum Arc and Erosion Characteristics of Spiral TMF Contacts with Different Materials

The Effect of Contact Material on Particles Behavior in High-Current Vacuum Arcs

High-Current Vacuum Arc Phenomena of Nanocrystalline Cucr25 Contact Material

High Current Vacuum Arc Phenomena of Nanocrystalline CuCr25 Contact Material

Investigation of vacuum arc ignition characteristics and erosion morphology microstructure characteristics of CuCr55 electrode contact materials

Experiment Investigation on Triggered Vacuum Arc under the Different Contact Materials

Inrush Current Arc Characteristics in Vacuum Interrupters with Axial Magnetic Field Contact and Butt-Type Contact

Experimental Investigation of High-Current Vacuum Arc Instability Modes under Transverse Magnetic Field

Effect of Micro-particles Impact Phenomena on Contact Surface in High Voltage Vacuum Interrupter after Conditioning

Prestrike Inrush Current Arc Behaviors in Vacuum Interrupters Subjected to a Transverse Magnetic Field and an Axial Magnetic Field

Minimum Arcing Interrupting Capability and Opening Velocity of Vacuum Interrupters: an Impact of Contact Diameters

Vacuum Arc Characteristics of a Novel Contact Consists of Arcing Contact and Main Contact

Experimental Investigation of Vacuum Arc Behavior under Different Contacts in Vacuum Interrupters

Arc Characteristics and Microstructure Evolution of W–Cu Contacts During the Vacuum Breakdown

Experimental Study and Characteristic Analysis of Vacuum Arc Between Cup-Type Axial Magnetic Contacts under Different Diameter-to-gap Ratios