Abstract:Due to the moderate degradation rates and acceptable biocompatibility, Zn-based alloys have attracted more and more attention as biodegradable materials. However, the inferior strength and ductility significantly limit their further applications. In this work, biodegradable Zn-2Cu-0.2Mn-xLi (x = 0, 0.1 and 0.38) alloys were developed with enhanced comprehensive mechanical properties. Also, these novel alloys were found to possess extraordinary antibacterial activity and good biocompatibility. Annealing and hot extrusion were performed on the as-cast alloys. The microstructures, mechanical properties, corrosion behavior, antibacterial ability, hemocompatibility and cytocompatibility of the alloys were systematically studied. Microstructure analysis indicates that primary e-CuZn4 particles are distributed in the Zn grains in all ascast alloys. Addition of Li leads to formation of beta-LiZn4 phase in eutectics and beta-LiZn4 precipitates within the Zn grains. In the as-annealed alloy, secondary epsilon-CuZn4 precipitates and fine beta-LiZn4 precipitates appear in the Zn matrix of the Li-containing alloys. All the as-extruded alloys reveal fibrous morphology and develop (0001) basal texture. Mechanical property test shows that all as-extruded alloys exhibit excellent strength and ductility which can fully meet the benchmark requirement for biodegradable materials. It is worth to notice that, Zn-2Cu-0.2Mn-0.38Li alloy has a tensile yield strength, ultimate tensile strength and elongation as high as 424 +/- 28.3 MPa, 445 +/- 11.1 MPa and 76 +/- 3.35%, respectively. The 24-day in vitro immersion test in the SBF solution shows that the corrosion rates were 0.212 +/- 0.007 mm/year for Zn-2Cu-0.2Mn, 0.197 +/- 0.005 mm/year for Zn-2Cu-0.2Mn-0.1Li and 0.184 +/- 0.008 mm/year for Zn-2Cu-0.2Mn-0.38Li, respectively. It indicates that addition of Li improves the corrosion resistance of the alloys. All as-extruded alloys have antibacterial rates of >= 99% and hemolysis rates of < 5%, exhibiting strong antibacterial activity and good hemocompatibility. The MC3T3-E1 cells show more than 95% viability in 25% extracts of all asextruded alloys in all culturing days. In addition, in this low concentration of extracts, the cells in the alloy groups exhibit good spreading morphology and high ALP expression, suggesting good cytocompatibility. (c) 2022 Elsevier B.V. All rights reserved.

Fabrication and Characterization of Novel Biodegradable Zn-Mn-Cu Alloys

Research on a Zn-Cu alloy as a biodegradable material for potential vascular stents application

Investigation on Microstructures, Mechanical Properties, and Corrosion Behavior of Novel Biodegradable Zn-xCu-xTi Alloys after Hot Rolling Fabricated by Self-Developed Newly Gradient Continuous Casting

Design and characterizations of novel biodegradable Zn-Cu-Mg alloys for potential biodegradable implants

Microstructure, Mechanical Properties and in Vitro Degradation Behavior of Novel Zn-Cu-Fe Alloys

Investigation on Microstructures, Mechanical Properties and in Vitro Corrosion Behavior of Novel Biodegradable Zn-2Cu-0.01Ti-xLi Alloys

Enhanced Mechanical Performance and Tailored Degradation Characteristics of Rolled Zn-0.8Li-0.4Mn Alloy

Biodegradable Zn-Cu-Mn alloy with suitable mechanical performance and in vitro degradation behavior as a promising candidate for vascular stents

Mechanical Properties, Degradation Behaviors and Biocompatibility Evaluation of a Biodegradable Zn-Mg-Cu Alloy for Cardiovascular Implants

An in Vitro and in Vivo Study of Biodegradable Zn-Cu-Li - Cu - Li Alloy with High Strength and Ductility Fabricated by Hot Extrusion Combined with Room-Temperature ECAP

Potential biodegradable Zn-Cu binary alloys developed for cardiovascular implant applications

Achieving Ultrahigh Strength and Ductility in Biodegradable Zn-xCu Alloys Via Hot-Rolling and Tailoring Cu Concentration

Development and Characterization of Zn-xCu-yTi-zMo Alloys for Biomedical Applications: a High-Throughput Gradient Continuous Casting Approach

300 MPa grade highly ductile biodegradable Zn-2Cu-(0.2-0.8)Li alloys with novel ternary phases

An in vitro and in vivo study of biodegradable Zn–Cu–Li alloy with high strength and ductility fabricated by hot extrusion combined with room-temperature ECAP

Microstructural Evolution, Mechanical Properties and Corrosion Mechanisms of Additively Manufactured Biodegradable Zn-Cu Alloys

Novel Zn-2Cu-0.2Mn-xLi (x = 0, 0.1 and 0.38) Alloys Developed for Potential Biodegradable Implant Applications

In Vitro Degradation Behavior of Novel Zn–Cu–Li Alloys: Roles of Alloy Composition and Rolling Processing

Development and characterization of ZnxCuyTizMo alloys for biomedical applications: A high-throughput gradient continuous casting approach

Development and Characterization of Zn-x Cu-y Ti-z Mo Alloys for Biomedical Applications: A High-Throughput Gradient Continuous Casting Approach

Optimization of Mechanical, Corrosion Properties and Cytotoxicity of Biodegradable Zn-Mn Alloys by Synergy of High-Pressure Solidification and Cold Rolling Process