Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Thermodynamically Consistent Directional Distortional Hardening of Mg Alloy: Experiments and Constitutive Modeling

Thermodynamically Consistent Constitutive Modeling of Distortional Hardening for Wrought Mg Alloys under Non-Proportional Loading

A Thermodynamically Consistent Distortional Hardening Model for AZ31 with Experimental Validation

Loading path dependent distortional hardening of Mg alloys: Experimental investigation and constitutive modeling on cruciform specimens

A Generalized Thermodynamically Consistent Distortional Hardening Model for Mg Alloys

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

Constitutive Modeling of Slip, Twinning and Detwinning for Mg Alloy and Inhomogeneous Evolution of Microstructure

Numerical simulation of plastic behavior and meso inhomogeneous deformation in AZ31 Mg alloy

A New Constitutive Model for Thermal Deformation of Magnesium Alloys

The Anisotropic Distortional Yield Surface Constitutive Model Based on the Chaboche Cyclic Plastic Model.

A Kinematic Hardening Constitutive Model for the Uniaxial Cyclic Stress–strain Response of Magnesium Sheet Alloys at Room Temperature

Anisotropic-Asymmetric Hardening Characterization of BCC/FCC/HCP Metals: Experiments and Modeling

Investigation on the inhomogeneous deformation of magnesium alloy during bending using an advanced plasticity model

Experiment and Modeling of Plastic Anisotropy for AZ31B Mg-Alloy

Mg-3Al-1Zn alloy deformed along different strain paths: Role of latent hardening

Anisotropy of wrought magnesium alloys: A focused overview

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Deformation Behavior of AZ31B Magnesium Alloys with Different Process States under Thermal Compression

Phenomenological Constitutive Model of Magnesium Alloy Under Uniaxial Cyclic Loading

Modeling of Anisotropic and Asymmetric Behaviour of Magnesium Alloys at Elevated Temperature Coupled with Ductile Damage

On a Modified Directional Distortional Hardening Model for Metal Plasticity