Abstract:It is expected that the demand for Metal Matrix Composite (MMCs) will increase in these applications in the aerospace and automotive industries sectors, strengthened AMC has different advantages over monolithic aluminium alloy as it has characteristics between matrix metal and reinforcement particles. However, adequate joining technique, which is important for structural materials, has not been established for (MMCs) yet. Conventional fusion welding is difficult because of the irregular redistribution or reinforcement particles. Also, the reaction between reinforcement particles and aluminium matrix as weld defects such as porosity in the fusion zone make fusion welding more difficult. The aim of this work was to show friction stir welding (FSW) feasibility for entering Al 6061/5 to Al 6061/18 wt. % SiCp composites has been produced by using stir casting technique. SiCp is added as reinforcement in to Aluminium alloy (Al 6061) for preparing metal matrix composite. This method is less expensive and very effective. Different rotational speeds,1000 and 1800 rpm and traverse speed 10 mm \ min was examined. Specimen composite plates having thick 10 mm were FS welded successfully. A high-speed steel (HSS) cylindrical instrument with conical pin form was used for FSW. The outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt. %) was 195 MPa at rotation speed 1800 rpm, the outcome revealed that the ultimate tensile strength of the welded joint (Al 6061/18 wt.%) was 165 MPa at rotation speed 1000 rpm, that was very near to the composite matrix as-cast strength. The research of microstructure showed the reason for increased joint strength and microhardness. The microstructural study showed the reason (4 %) for higher joint strength and microhardness. due to Significant of SiCp close to the boundary of the dynamically recrystallized and thermo mechanically affected zone (TMAZ) was observed through rotation speed 1800 rpm. The friction stir welded ultimate tensile strength Decreases as the volume fraction increases of SiCp (18 wt.%).

Deformation and Fracture of AMC under Different Heat Treatment Conditions and Its Suitability for Incremental Sheet Forming

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Combined Effect of Particle Reinforcement and T6 Heat Treatment on the Compressive Deformation Behavior of an A357 Aluminum Alloy at Room Temperature and at 350 °C

On the Fracture Characterization in Double-Sided Incremental Forming of Ti6al4v Sheets at Elevated Temperatures

A review on the deformation mechanism and formability enhancement strategies in incremental sheet forming

Formability Analysis of Electrically Assisted Double-Side Multi-Point Incremental Sheet Forming

Increasing the Formability of CP-Ti During Incremental Sheet Forming with an Auxiliary Sheet

Investigation of Pre-Aged Hardening Single-Point Incremental Forming Process and Mechanical Properties of AA6061 Aluminum Alloy

Mechanical Test on Aluminum Alloy with Maximal Soluble SiC Reinforcement

Microstructural analysis of AA8079 alloy sheets formed by friction stir incremental forming

Experimental Investigations on Friction Stir Assisted Single Point Incremental Forming of Low-Ductility Aluminum Alloy Sheet for Higher Formability with Reasonable Surface Quality

Analytical and Experimental Investigations on Deformation Mechanism and Fracture Behavior in Single Point Incremental Forming

Numerical Simulation of the Mechanical Properties and Fracture of SiCp/6061Al Composite Materials Based on Microstructure

Comprehensive Understanding of the Mechanical Properties and Microstructure Evolution of Aluminum Alloy/steel Laminates During Friction Stir-Assisted Incremental Forming with Synchronous Bonding Process

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite

Investigation of the Effect of Forming Parameters in Incremental Sheet Forming Using a Micromechanics Based Damage Model

Experimental Investigations on Deformation Characteristics in Microstructure Level During Incremental Forming of AA5052 Sheet

Microstructure and mechanical properties of Al-Mg-Si alloy during solution heat treatment and forging integrated forming process

Investigation of Microstructures and Mechanical Properties of SiC/AA2024 Nanocomposites Processed by Powder Metallurgy and T6 Heat Treatment

Study on Hot Deformation Behavior and Workability of Squeeze-Cast 20 Vol%sicw/6061al Composites Using Processing Map

A Study of Microstructural Tensile and Fatigue Properties Coupled with Digital Image Correlation of Hybrid Manufactured Inconel 718 Parts by Extrusion and Powder Bed Fusion