Abstract:Perovskite solar cells based on the inorganic/organic hybrid perovskite have attracted increasing attention over the past 3 years. Many studies have been done in this area. Controling the morphology of the perovskite film is an effective way to improve the photoelectric conversion efficiency of the devices. In our reserch, we studied the influence of structure and morphology of perovskite films on the performance of the organic-inorganic hybrid perovskite solar cells which prepared by a sequential deposition method. Mesoporous TiO2 scaffold were introduced as electron collecting layer. Lead iodide (PbI2) was then spin cast on the TiO2 scaffold. The PbI2 subsequently transformed into the perovskite (CH3NH3PbI3) by dipping the TiO2/PbI2 film into a solution of CH3NH3I. We studied the difference between the PbI2 film with or without drying under room temperature after spin-coating. Through drying under room temperature, larger pores formed in the PbI2 film. While without drying under room temperature, smaller and shallower pores formed in the PbI2 film. The results show that larger pores in PbI2 film leads to more complete transformation of PbI2 to CH3NH3PbI3 and larger CH3NH3PbI3 particles. CH3NH3PbI3 films were prepared with three different processes: (a) direct dipping the PbI2 film with smaller pores into the CH3NH3I solution; (b) direct dipping the PbI2 with larger pores into the CH3NH3I solution; (c) dipping the PbI2 with larger pores into the CH3NH3I solution after pre-wetting. The resulting CH3NH3PbI3 films were studied with SEM, UV-vis absorption spectrum and XRD. The particles size of the CH3NH3PbI3 are 150, 250 and 350 rim for process (a), (b) and (c) respectively. CH3NH3PbI3 films fabricated through process (a) show insufficient absorption due to the insufficient transformation of the PbI2. The pre-wetting procedure leads to slower reaction result in larger CH3NH3PbI3 particle size. Devices with proper size of CH3NH3PbI3 particles show the highest photoelectric conversion efficiency. An efficiency of 13.5% was achieved with a J(sc) of 17.8 mA/cm(2), a V-oc of 1.05 V and a FF of 72.5%.

The impacts of PbI2 purity on the morphology and device performance of one-step spray-coated planar heterojunction perovskite solar cells

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

The Effect of Component Defects on the Performance of Perovskite Devices and the Low-Cost Preparation of High-Purity PbI2

Replacing PbI2 by MAPbI(3) to Realize Large Grain Size and Reduced Hysteresis for Highly Efficient Perovskite Solar Cells

Regulation of Lead Iodide Crystallization and Distribution for Efficient Perovskite Solar Cells

Trace Water in Lead Iodide Affecting Perovskite Crystal Nucleation Limits The Performance of Perovskite Solar Cells

Influence of Structure and Morphology of Perovskite Films on the Performance of Perovskite Solar Cells

Intercalation Crystallization of Phase-Pure Α-Hc(nh2)2pbi3upon Microstructurally Engineered PbI2thin Films for Planar Perovskite Solar Cells

Precise Control of PbI2 Excess into Grain Boundary for Efficacious Charge Extraction in Off-Stoichiometric Perovskite Solar Cells

Anti-solvent Engineering to Rapid Purify PbI2 for Efficient Perovskite Solar Cells

Replacing PbI<sub>2</sub> by MAPbI<sub>3</sub> to Realize Large Grain Size and Reduced Hysteresis for Highly Efficient Perovskite Solar Cells

Improvement of Colloidal Characteristics in a Precursor Solution by a PbI2-(DMSO)2 Complex for Efficient Nonstoichiometrically Prepared CsPbI2.8Br0.2 Perovskite Solar Cells

High-Performance Simple-Structured Planar Heterojunction Perovskite Solar Cells Achieved by Precursor Optimization.

Controlled Crystallization of CH3NH3PbI3 Films for Perovskite Solar Cells by Various PbI2(X) Complexes

Pressure-Assisted Space-Confinement Strategy to Eliminate PbI 2 in Perovskite Layers toward Improved Operational Stability

High Efficient Planar-Heterojunction Solar Cells Achieved by Using A Smooth Ch3nh3pbi3 Film Via A New Approach of Forming the Pbi2 Nanostructure Together with Strategically High Ch3nh3i Concentration

The controllability of PbI2 morphology via nanorod-shaped underlying layer for solution-based perovskite two-step sequential deposition

Modulation of Nucleation and Crystallization in PbI2 Films Promoting Preferential Perovskite Orientation Growth for Efficient Solar Cells

A controllable fabrication of grain boundary PbI2 nanoplates passivated lead halide perovskites for high performance solar cells

A Simple Fabrication of CH3NH3PbI3 Perovskite for Solar Cells Using Low-Purity PbI2

Aqueous synthesis of perovskite precursors for highly efficient perovskite solar cells