Abstract:We describe here the relationship between grain structure, deformation mechanism and fracture characteristics in an austenitic stainless steel. This was accomplished using the novel concept of phase reversion that enabled a wide range of grain size from nanograined/ultrafine grained (NG/UFG) to coarse-grained (CG) regime to be obtained in a single material through change in temperature-time annealing sequence. In the NG/UFG structure, a marked increase in abundance of stacking faults (SFs) and twin density with strain was observed that led to a decrease in the average spacing between adjacent SFs, thus converting stacking faults into twins. Twinning in NG/UFG structure involved partial dislocations and their interaction with the grain boundaries, including SF overlapping and the coordinated nucleation of partial dislocations from the grain boundaries. The plastic zone in the NG/UFG structure resembled a network knitted by the intersecting twins and SFs. With SFE ~30 mJ/m2, the minimum stress for twin nucleation was ~250 MPa for the experiment steel and the corresponding optimal grain size (dop) wa ~120 nm. In contrast, in the CG structure, strain induced martensite formation was the deformation mechanism. The difference in the deformation mechanism led to a clear distinction in the fracture behavior from striated fracture in high strength-high ductility NG/UFG alloy to microvoid coalescence in the low strength-high ductility CG counterpart. The underlying reason for the change in fracture behavior was consistent with change in deformation mechanism from nanoscale twinning in NG/UFG alloy to strain-induced martensite in the CG alloy, which is related to change in the stability of austenite with grain size. An analysis of critical shear stress required to initiate twinning partial dislocations in comparison to that required to nucleate shear bands is presented. The appearance of striated fracture in the NG/UFG alloy suggests a quasi-static step wise crack growth process.

Deformation Mechanism and Ductile Fracture Behavior in High Strength High Ductility Nano/ultrafine Grained Fe-17Cr-6Ni Austenitic Steel

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

The Direct and Indirect Effects of Nanotwin Volume Fraction on the Strength and Ductility of Coarse-Grained Metals

Computer Simulation of Strength and Ductility of Nanotwin-Strengthened Coarse-Grained Metals

Tensile Failure Modes in Nanograined Metals with Nanotwinned Regions

Microstructures and Deformation Behavior of Nano-Grained and Ultrafine-Grained High-Mn Austenitic Steel Fabricated by Asymmetric-Symmetric Rolling

Micromechanism involved in ultrafine grained ferrite/martensite dual phase steels strengthened by nanoscale Cu-rich precipitates

The significance of deformation mechanisms on the fracture behavior of phase reversion-induced nanostructured austenitic stainless steel

Enhanced Mechanical Properties Of Nano/Ultrafine-Grained Structure Formed By Martensite Reversion In 18cr-8ni Austenitic Stainless Steel

High Tensile Ductility and High Strength in Ultrafine-Grained Low-Carbon Steel

Probing the Impact of Grain Interior and Grain Boundaries on the Mechanical Behavior of a High-Mn Austenitic Steel

Grain refinement strengthening mechanism of an austenitic stainless steel: critically analyze the impacts of grain interior and grain boundary

A Grain Level Model for Deformation and Failure of Ultrafine-Grained Tungsten

Deformation and Fracture Mechanisms of Gradient Nanograined Pure Ti Produced by a Surface Rolling Treatment

Ultrahigh strength martensite-austenite dual-phase steels with ultrafine structure: The response to indentation experiments

In-situ three-dimensional X-ray investigation on micro ductile fracture mechanism of a high-Mn steel with delayed necking effect

Nanograin formation in dimple ridges due to local severe-plastic-deformation during ductile fracture

On the mechanical behavior of austenitic stainless steel with nano/ultrafine grains and comparison with micrometer austenitic grains counterpart and their biological functions

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Deformation mechanism of a strong and ductile maraging steel investigated using in-situ X-ray synchrotron diffraction

Transformation plasticity in high strength, ductile ultrafine-grained FeMn alloy processed by heavy ausforming