Abstract:A high-performance polypropylene hollow fiber membrane (PP-HFM) was prepared by using a binary environmentally friendly solvent of polypropylene as the raw material, adopting the thermally induced phase separation (TIPS) method, and adjusting the raw material ratio. The binary diluents were soybean oil (SO) and acetyl tributyl citrate (ATBC). The suitable SO/ATBC ratio of 7/3 was based on the size change of the L-L phase separation region in PP-SO/ATBC thermodynamic phase diagram. Through the characterization and comparison of the basic performance of PP-HFMs, it was found that with the increase of the diluent content in the raw materials, the micropores of outer surface of the PP-HFM became larger, and the cross section showed a sponge-like pore structure. The fluoropolymer, Hyflon ADx, was deposited on the outer surface of the hollow fiber membrane using a physical modification method of solution dipping. After modification, the surface pore size of the Hyflon AD40L modified membranes decreased; the contact angle increased to around 107°; the surface energy decreased to 17 mN·m-1; and the surface roughness decreased to 17 nm. Hyflon AD40L/PP-HFMs also had more water resistance properties from the variation of wetting curve. For biocompatibility of the membrane, the adsorption capacity of the modified PP membrane for albumin decreased from approximately 1.2 mg·cm-2 to 1.0 mg·cm-2, and the adsorption of platelets decreased under fluorescence microscopy. The decrease in blood cells and protein adsorption in the blood prolonged the clotting time. In addition, the hemolysis rate of modified PP membrane was reduced to within the standard of 5%, and the cell survival rate of its precipitate was above 100%, which also indicated the excellent biocompatibility of fluoropolymer modified membrane. The improvement of hydrophobicity and blood compatibility makes Hyflon AD/PP-HFMs have the potential for application in membrane oxygenators.

Surface modification of polysulfone hollow fiber membrane for extracorporeal membrane oxygenator using low-temperature plasma treatment

Surface Monofunctionalized Polymethyl Pentene Hollow Fiber Membranes by Plasma Treatment and Hemocompatibility Modification for Membrane Oxygenators

Hemocompatibility and Oxygenation Performance of Polysulfone Membranes Grafted with Polyethylene Glycol and Heparin by Plasma-Induced Surface Modification

Polyethylene Glycol Acrylate-Grafted Polysulphone Membrane for Artificial Lungs: Plasma Modification and Haemocompatibility Improvement

Engineering of hemocompatible and antifouling polyethersulfone membranes by blending with heparin-mimicking microgels

Hollow fiber membrane modification with functional zwitterionic macromolecules for improved thromboresistance in artificial lungs.

Fabrication, Characterization, and Hemocompatibility Investigation of Polysulfone Grafted with Polyethylene Glycol and Heparin Used in Membrane Oxygenators.

A Novel Polysulfone-Based Affinity Membrane with High Hemocompatibility: Preparation and Endotoxin Elimination Performance

Hydrophilic modification of a PSU membrane with block copolymer of PS-b-SBMA

Improving Hemocompatibility of Polysulfone Membrane by UV-Assisted Grafting of Sulfonated Chitosan

Heparin-modified polyether ether ketone hollow fiber membrane with improved hemocompatibility and air permeability used for extracorporeal membrane oxygenation

Applying a Hydrophilic Modified Hollow Fiber Membrane to Reduce Fouling in Artificial Lungs

Facile Preparation of Heparinized Polysulfone Membrane Assisted by Polydopamine/Polyethyleneimine Co-Deposition for Simultaneous Ldl Selectivity and Biocompatibility

Preparation of Hyflon AD/Polypropylene Blend Membrane for Artificial Lung

Hydrophilic modified PES asymmetric membrane via thermal cross-linking for artificial lung application

Preparation, Characterization, and Performance Evaluation of Polysulfone Hollow Fiber Membrane with PEBAX or PDMS Coating for Oxygen Enhancement Process

Preparation and characterization of membrane oxygenator-oriented polysulfone asymmetric membranes

Improvement hemocompatibility of antithrombotic PMP hollow fiber membranes based on the modification of zwitterionic polymer in ECMO application

Development of zwitterionic sulfobetaine block copolymer conjugation strategies for reduced platelet deposition in respiratory assist devices

Improving the hydrophilicity and fouling-resistance of polysulfone ultrafiltration membranes via surface zwitterionicalization mediated by polysulfone-based triblock copolymer additive

Surface Modification of Polypropylene Macroporous Membrane to Improve Its Antifouling Characteristics in a Submerged Membrane-Bioreactor: H(2)O Plasma Treatment.