Abstract:Surface layer with heterogeneous microstructures (SLHM), characterized by hardened spots discretely embedded in a soft substrate, can be prepared by laminar plasma quenching (LPQ) to improve the wear resistance of the railway rail. However, severe rolling contact fatigue (RCF) cracks and spalling would occur in the hardened spots that only consist of quenched microstructure. This study analyzed the RCF damage mechanism of the LPQ prepared hardened spots by contact simulation. To improve the RCF resistance while maintaining the high wear resistance of the treated rail, a novel SLHM, whose discrete hardened spots are surrounded by transitional zone with the hardness lower than that of the quenched zone but higher than that of the substrate, was proposed and prepared by laminar plasma quenching-tempering (LPQT). Then, twin-disc tests and contact simulations were conducted to investigate the wear and RCF resistances of the LPQT treated rail steel. Results showed that the cause of the severe RCF cracks and spalling at the entry side of the LPQ prepared hardened spots was that the cyclic tensile stress at the entry side was always higher than that at the exit side under the cyclic rolling contact loading. The high tensile stress at the entry side of the LPQ prepared hardened spots resulted from the elastic deformation induced by tensile plastic deformation of the neighboring substrate. When the thickness of the transitional zone was about 0.1 mm, the generation of severe RCF cracks and spalling was significantly inhibited in the LPQT prepared hardened spots because the transitional zone decreases the cyclic tensile stress at the entry side of the quenched zone. Besides, the wear loss of such LPQT treated rail steel was only increased by 18.1 % compared with that of the LPQ treated rail steel, indicating that the wear resistance of the LPQT treated rail steel was not significantly reduced. These findings are promising for designing the microstructure of the surface layer to obtain wear-resistant rail with high RCF resistance.

Couple of Biomimetic Surfaces with Different Morphologies for Remanufacturing Nonuniform Wear Rail Surface

Effect of Distribution of Striated Laser Hardening Tracks on Dry Sliding Wear Resistance of Biomimetic Surface

Study on the Relationship Between Intervals among Laser Stripes and the Abrasion Resistance of Biomimetic Laser Textured Surfaces

Bio-inspired Wearable Characteristic Surface: Wear Behavior of Cast Iron with Biomimetic Units Processed by Laser

Wear Behavior of Medium Carbon Steel with Biomimetic Surface under Starved Lubricated Conditions

Anti-wear properties on 20CrMnTi steel surfaces with biomimetic non-smooth units

Bionic Laser Surface Remelting for the Wear Performance after Thermal Fatigue of B2 Die Steel Based on Surface Stress Simulation

Influence of Varying Forms of Bionic Units on Repairing Remaining Quenching Surface of Gray Cast Iron

Experimental Investigation On Anti-Wear Of A Bionic Non-Smooth Surface Made By Laser Texturing

Effect of the Orientation of Laser Stripes on the Abrasion Resistance of Biomimetic Laser Textured Surfaces

Experimental Investigation on Anti-wear of ABionic Non-smooth Surface Made by LaserTexturing

Investigation on Anti-Wear Ability of Bionic Nonsmooth Surfaces Made by Laser Texturing

Mechanism and Improvement of the Rolling Contact Fatigue of the Surface Layer with Heterogeneous Microstructures of the Rail Steel Treated by Laminar Plasma Jet

Experiment Research on Wear Mechanism with Bionic Non-Smoothed Surface

Experimental Investigation on the Wear and Damage Behaviors of Machined Wheel-Rail Materials under Dry Sliding Conditions

Laser-induction hybrid cladding of different coatings on rail surface: Microstructure, wear properties and contact fatigue behaviors

Surface Morphology of Laser Tracks Used for Forming the Non-Smooth Biomimetic Unit of 3cr2w8v Steel under Different Processing Parameters

A novel laser surface compositing by selective laser quenching to enhance railway service life

Wear Resistance of Machine Tools' Bionic Linear Rolling Guides by Laser Cladding

Gas–Solid Erosive Wear of Biomimetic Pattern Surface Inspired from Plant

Experiment on Wear Resistance of 55 Steel Bionic Non-smoothed Surfaces at High Temperature