Abstract:The pneumatic metering device has the advantages of high qualified index, less mechanical damage to seeds and good adaptability for high-speed operation. But traditional calculation method is not capable of analyzing the law of seeds motion because of the complex stress state. Discrete element method (DEM) is the key method to solve the above problem. However, physical characteristics parameters of particles, mainly consisting of static friction coefficient and rolling friction coefficient between corn seeds, are key factors for reliable simulation results in the DEM. Due to the difference between corn seeds and simulation particles in surface shape and size, the actual physical parameters of corn seeds are not suitable for the EDEM (enhanced discrete element method). Particles models established in the EDEM are rougher than corn seeds, which leads to the distortion of simulation results. Therefore calibration works for particle parameters are essential. In this paper, a new method was proposed for actively seeking the target parameters based on regression analysis. It was estimated that repose angle was commonly influenced by static friction coefficient and rolling friction coefficient between corn seeds. All factors simulation experiments were conducted to obtain the regression equations, of which the tangent value of repose angle at different contact material was separately taken as the dependent variables, and the static friction coefficient and rolling friction coefficient between corn seeds were taken as independent variables. In order to decrease the measuring error, MATLAB software was used for images acquisition and analysis. The variance analysis showed that the static friction coefficient and rolling friction coefficient between corn seeds had significant influence on the repose angle and natural heaping angle separately at significance level of 5%. The tangent value of repose angle had an increase trend with the increase of static friction coefficient and rolling friction coefficient between corn seeds. For the first test with organic plate, it had a bigger increase when the static friction coefficient was at 0-0.2 and then increased slowly, at this time which was mainly influenced by the rolling friction coefficient. For the second test with aluminum plate, it also increased with the increase of static friction coefficient and rolling friction coefficient between corn seeds in a consistent state. By the simulation tests, 2 regression equations were obtained. For solving the independent variables, the actual tangent values of repose angle with different contact material were measured by the actual tests and taken as the dependent variables. By this way, the static friction coefficient of 0.0338 and the rolling friction coefficient of 0.0021 between corn seeds were obtained. Verification tests with calibrated physical parameters were carried out. Results showed that the tangent values of repose angle were consistent with the actual tests. The simulation model of corn seeds was composed of multiple small spherical particles. There were sunk areas between adjacent seeds, so the contact area between corn seeds increased and meanwhile the friction force was increased. Corresponding relation between actual seeds and simulation model was found by this calibration method. The boundary of repose angle was extracted to compare the simulation and actual test results, which verified that the calibrated physical parameters were applicable for the EDEM and the method was feasible.

Determination of the Coefficient of Rolling Friction of an Irregularly Shaped Maize Particle Group Using Physical Experiment and Simulations

Effect of coefficient of rolling friction on internal force of particles pile

Experimental Determination of the Coefficient of Restitution of Particle-Particle Collision for Frozen Maize Grains

Experimental Determination of Parameter Effects on the Coefficient of Restitution of Differently Shaped Maize in Three-Dimensions

DEM Parameter Calibration of Maize Seeds and the Effect of Rolling Friction

Experiment and simulation of rolling friction characteristic of corn seed based on high-speed photography

Determination of the Energetic Coefficient of Restitution of Maize Grain Based on Laboratory Experiments and DEM Simulations

Studying on the Upper Limit of the Coarse-Grained DEM Model for Simulating Mixing Processes in a Rolling Drum with Complex Wall Boundary

A Calibration Method for Contact Parameters of Maize Kernels Based on the Discrete Element Method

Friction coefficient calibration of corn stalk particle mixtures using Plackett-Burman design and response surface methodology

Investigation of Modeling Non-Spherical Particles by Using Spherical Discrete Element Model with Rolling Friction

Calibration Method of Contact Characteristic Parameters for Corn Seeds Based on EDEM

Examination Milling Non-Uniformity in Friction Rice Mills Using by Discrete Element Method and Experiment

An Approach to and Validation of Maize-Seed-assembly Modelling Based on the Discrete Element Method

Determination of Friction Characteristics of Corn Ears at Varying Factors in Mechanical Peeling

Calibration of discrete element parameters for simulating wheat crushing

The Effects of Friction Characteristic of Particle on Milling Process in a Horizontal Rice Mill

Evaluation of static and rolling friction coefficients of granulated sugar using the discrete element method in a rolling mode rotating drum

A study on the modelling method of maize-seed particles based on the discrete element method

Calibration of the discrete element method: Strategies for spherical and non-spherical particles

The Influence of Rolling Resistance on Granular Responses Under Triaxial Loading Paths