Abstract:Forming limit diagrams (FLDs) are very important in predicting the behavior of the sheet. Therefore, predicting and drawing these diagrams by theoretical and experimental methods has been one of the main objectives of this paper. In this paper, the formability behavior of 5083 aluminum sheet was investigated by considering the strain hardening behavior. Tensile tests has performed in seven directions 0°, 15°, 30°, 45°, 60°, 75° and 90° from the rolling direction due to identify and calibrate coefficients of BBC2008 advanced yield criteria. The yield stresses was defined in the plane strain mode, also the anisotropy coefficients and the appropriate error function were extracted and then the relationships of the plane strain yield stress were added to the error function. The error function was optimized using Genetic Algorithm and limit strains were calculated using yield coefficients. The results showed that if the strain hardening exponent increases by 0.1, the limit strains increase by 30 to 40%. Also the results showed that the initial imperfection factor ( 𝑓 0 ) has a great effect on determining the FLD and with a very small change, it has a great effect on the FLD; So that by increasing this factor to about 0.016, the values of the limit strains are almost doubled. Using the results of this paper and having sheet properties such as yield strengths and anisotropy coefficients and proper selection of yield criteria, the FLD of different sheets to be theoretically determined with acceptable accuracy. [1] Plastic Instability and Fracture in Sheet Stretched over Rigid Punches. [2] Application of strain analysis to sheet metal forming problems in the press shop. [3] On discontinuous plastic states, with special reference to localized necking in thin sheets. [4] Limit strains in the processes of stretch-forming sheet metal. [5] The influence of strain-path changes on forming limit diagrams of A1 6111 T4. [6] Investigation of formability of low carbon steel sheets by forming limit diagrams. [7] Theoretical determination of forming limit diagram for steel, brass and aluminum alloy sheets. [8] Experimental and numerical evaluation of forming limit diagram for Ti6Al4V titanium and Al6061-T6 aluminum alloys sheets. [9] Experimental and numerical analysis of forming limit diagram (FLD) and forming limit stress diagram (FLSD). [10] Forming limit and fracture mechanism of ferritic stainless steel sheets. [11] Calculation of forming limit diagrams using Hill's 1993 yield criterion. [12] The effects of anisotropic yield functions and their material parameters on prediction of forming limit diagrams. [13] The Effect of Advanced BBC2003, Yld2004 and BBC2008 Yield Criteria on FLDs Based on MK, Swift's and Hill's Models. [14] An experimental and theoretical investigation for determination of yield criteria parameters... [15] The forming limit curve for multiphase advanced high strength steels... [16] Forming limits of dual phase steels using crystal plasticity in conjunction with MK approach. [17] Prediction of FLD for sheet metal by considering through-thickness shear stresses. [18] Investigation on the effective range of the through thickness shear stress... [19] Controlling factors of forming limit curve: A review. [20] Crystal plasticity finite element – Marciniak-Kuczynski approach with surface roughening effect... [21] Plane stress yield criterion for highly anisotropicsheet metals. [22] Techniques of measurement of body composition Part II. [23] An improved analytical description of orthotropy in metallic sheets. [24] A study of microstructure and tribological properties of Al 5083 MMC processed by direct extrusion. [25] A novel and simple method for the measurement of plane strain work hardening.

Experimental and Theoretical Investigations of the Forming Limit of 5754O Aluminum Alloy Sheet under Different Combined Loading Paths

Effect of nonlinear strain paths on forming limits under isotropic and anisotropic hardening

Effect of Through-Thickness Normal Stress on Forming Limits under Yld2003 Yield Criterion and M-K Model

Comparative Analysis Between Stress- and Strain-Based Forming Limit Diagrams for Aluminum Alloy Sheet 1060

Experimental and Theoretical Study of Formability Behavior of Aluminum Alloy 5083 Sheet for Determination of Advanced Anisotropic Yield Criteria Coefficient and Prediction of Forming Limit Diagram

Prediction of Strain Path Changing Effect on Forming Limits of AA 6111-T4 Based on a Shear Ductile Fracture Criterion

Forming Limit Prediction for Two-Stage Aluminum Alloy Sheet Forming Process Considering the Effect of Normal Stress

Theoretical and Numerical Investigation of the Limit Strain of a 5754-O Aluminum Alloy Sheet Considering the Influence of the Hardening Law

Numerical Investigation into the Effect of Uniaxial and Biaxial Pre‐Strain on Forming Limit Diagram of 5083 Aluminum Alloy

Prediction of Forming Limit for Aluminum Alloy Sheet Coupling with Temperature and Strain Rate

Forming Limit of FSW Aluminum Alloy Blank Based on a New Constitutive Model

Numerical prediction and experimental validation of forming limit curves of laminated half-hard aluminum sheets

Sheet Metal Forming Limit Prediction with Maximum Thickness Reduction Ratio

Prediction of Forming Limits for Anisotropic Materials with Nonlinear Strain Paths by an Instability Approach

Theoretical failure investigation for sheet metals under hybrid stretch-bending loadings

On Practical Forming Limits in Superplastic Forming of Aluminum Sheet

Determination of Forming Limit for Aluminium Alloy Sheet Eliminating the Interferences of Through-Thickness Stress and Non-Linear Strain Path

Finite element simulations and experimental verifications for forming limit curve determination of two-layer aluminum/brass sheets considering the incremental forming process

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Comparative Investigation of the Experimental Determination of AA5086 FLCs under Different Necking Criteria

Forming Limit Evaluation by Considering Through-Thickness Normal Stress: Theory and Modeling