Electrochemical assay of lipid kinase activity facilitated by liposomes

Tao Gao,Shiyu Gu,Chaoli Mu,Meiling Zhang,Jie Yang,Ping Liu,Genxi Li

DOI: https://doi.org/10.1016/j.electacta.2017.08.190

IF: 6.6

2017-01-01

Electrochimica Acta

Abstract:A liposome-based electrochemical biosensor has been first proposed for lipid kinase activity, which ensures simplicity, sensitivity and efficiency.

What problem does this paper attempt to address?

Bioelectronic modulation of single-wavelength localized surface plasmon resonance (LSPR) for the detection of electroactive biomolecules

Zetao Chen,Fenni Zhang,Yanli Lu,Yaru Li,Guang Liu,Jianzhen Shan,Qingjun Liu

DOI: https://doi.org/10.1016/j.cclet.2021.10.027

IF: 9.1

2022-01-01

Chinese Chemical Letters

Abstract:The simplification of localized surface plasmon resonance (LSPR) detection can further promote the development of optical biosensing application in point-of-care testing. In this study, we proposed a simple light emitting diode (LED) based single-wavelength LSPR sensor modulated with bio-electron transfers for the detection of electroactive biomolecules. Indium tin oxide electrode loaded with nanocomposites of polyaniline coated gold nanorod was used as LSPR chip, and the applied electric potential was scanned at the LSPR chip for single-wavelength LSPR biosensing. Under the scanning of applied potentials, biological electron transfer of redox reaction was employed to demonstrate the bioelectronic modulation of single-wavelength LSPR for selective electroactive biomolecule detection. Without any additional recognition material, electroactive biomolecules uric acid and dopamine were detected directly with a sensitivity of 5.05 mu mol/L and 7.11 mu mol/L at their specific oxidation potentials, respectively. With the simplified optical configuration and selective bioelectronic modulation, the single-wavelength LSPR sensor is promising for the development of simple, low-cost, and high specificity optical biosensor for point-of-care testing of electroactive biomolecules. (C) 2021 Published by Elsevier B.V. on behalf of Chinese Chemical Society and Institute of Materia Medica, Chinese Academy of Medical Sciences.
Enediol-Ligands-Encapsulated Liposomes Enables Sensitive Immunoassay: A Proof-of-Concept for General Liposomes-Based Photoelectrochemical Bioanalysis.

Li-Ping Mei,Fei Liu,Jian-Bin Pan,Wei-Wei Zhao,Jing-Juan Xu,Hong-Yuan Chen

DOI: https://doi.org/10.1021/acs.analchem.7b01291

IF: 7.4

2017-01-01

Analytical Chemistry

Abstract:Sensitive photoelectrochemical (PEC) bioanalysis usually relies on enzyme-assisted signal amplification. This work describes the first proof-of-concept study for liposome-based PEC bioanalysis. Specifically, unilamellar liposomes were prepared and then utilized to carry the enediol-ligands and antibodies within their internal cavities and upon their external surfaces, respectively. On the other hand, the 96-well plate was used for accommodating the sandwich immunocomplexing, and then the confined liposomes were directed to release the encapsulated enediol-ligands into an individual well. The subsequent in situ sensitization of the TiO2 nanoparticles (NPs) electrode was then used to transduce the recognition events. This facile strategy allows for sensitive immunoassay without the involvement of laborious electrode fabrication and enzymatic amplification. Importantly, the protocol can be extended as a general PEC method for numerous other targets of interest. We believe this work could offer a new perspective for the rational implementation of various liposome complexes for novel PEC bioanalysis.
Electrochemical detection of kinase by converting homogeneous analysis into heterogeneous assay through avidin-biotin interaction

Yong Chang,Xiaohua Ma,Ting Sun,Lin Liu,Yuanqiang Hao

DOI: https://doi.org/10.1016/j.talanta.2021.122649

IF: 6.1

2021-11-01

Talanta

Abstract:In the classical heterogeneous electrochemical assay, phosphorylation of peptide substrate is usually performed on the solid-liquid surface. However, immobilization of probe on the solid surface may limit the interaction between the reaction site of probe and the active center of kinase due to the steric hindrance effect. In this work, we proposed a heterogeneous electrochemical method for kinase detection, in which the probe is immobilization-free during the phosphorylation reaction. A biotinylated peptide was used as the kinase substrate. After phosphorylation, the biotinylated phosphopeptide was captured by the neutravidin (NA)-modified electrode through the avidin-biotin interaction. The phosphate groups on the electrode surface were then recognized by the conjugates preformed between biotinylated Phos-tag™ (Bio-tag-Phos) and ferrocene (Fc)-capped NA-modified gold nanoparticle (Fc-AuNP-NA). The method integrates the advantages of homogeneous reaction and heterogeneous detection with high simplicity, sensitivity and specificity. The strategy can be applied to design other heterogeneous biosensors without the immobilization of probe during the enzyme catalyzed reaction.

chemistry, analytical
Multiple Signal Amplification Electrogenerated Chemiluminescence Biosensors for Sensitive Protein Kinase Activity Analysis and Inhibition.

Zhiyong Yan,Feng Wang,Pingye Deng,Yu Wang,Kai Cai,Yanhui Chen,Zonghua Wang,Yang Liu

DOI: https://doi.org/10.1016/j.bios.2015.02.006

IF: 12.545

2015-01-01

Biosensors and Bioelectronics

Abstract:A novel electrogenerated chemiluminescence (ECL) biosensor was built for the detection of kinase activity based on multiple signal amplification nanoprobes. In this strategy, the Xanthine oxidase (XOD) and 5′-phosphate group end DNA conjugated AuNPs was integrated with the phosphorylated peptide by Zr4+. The XOD on gold nanoparticles can catalyze dissolved oxygen to produce H2O2 in the presence of hypoxanthine (HA) which acts as a coreactor for luminol ECL reaction. In addition, due to the excellent catalytic activity of gold nanoparticle toward luminol ECL reaction and its large surface area that can accommodate large number of XOD and DNA on the surface, the ECL signal of luminol was significantly amplified, affording a highly sensitive ECL analysis of kinase activity. The as-proposed biosensor presents a low detection limit of 0.09UmL−1 for protein kinase A (PKA) activity, wide linear range (from 0.1 to 10UmL−1) and excellent stability even in serum samples. This biosensor can also be applied for quantitative kinase inhibitor evaluation. The robust ECL biosensor provides a valuable tool for the high throughput assay in the applications of clinic diagnostic and therapeutic.
A simple strategy to monitor lipase activity using liquid crystal-based sensors

Qiong-Zheng Hu,Chang-Hyun Jang

DOI: https://doi.org/10.1016/j.talanta.2012.05.016

IF: 6.1

2012-09-15

Talanta

Abstract:In this study, we developed a simple label-free technique for monitoring the enzymatic activity of lipase using liquid crystal (LC)-based sensors. The optical response of LCs changed from a bright to dark appearance when an aqueous solution of lipase was in contact with a nematic LC, 4-cyano-4'-pentylbiphenyl (5CB), that was doped with glyceryl trioleate, which is a glyceride that can be enzymatically hydrolyzed by lipase. Since the oleic acid released from the enzymatic reaction could spontaneously form a self-assembled monolayer at the aqueous/LC interface due to its amphiphilic property, the orientation of the LCs transited from a planar to homeotropic state, which induced a change in the optical response of the LCs. We did not observe a bright-to-dark shift in the optical appearance of LCs when pure 5CB was immersed into the lipase solution. Moreover, we further confirmed the specificity of the enzymatic reaction by transferring an aqueous buffer solution not containing an analyte, or with bovine serum albumin (BSA) or trypsin onto the interface of aqueous solutions and the glyceryl trioleate-doped 5CB, which did not produce any distinctive contrast in the optical appearance. These results suggest the feasibility of measuring the enzymatic activity of lipase using the LC-based sensing technique. Furthermore, our strategy could also be used for the preparation of a self-assembled monolayer of carboxylates at the aqueous/LC interface.
Electrochemical analysis of enzyme based on the self-assembly of lipid bilayer on an electrode surface mediated by hydrazone chemistry.

Juan Zhang,Xiaonan Wang,Tingjun Chen,Chang Feng,Genxi Li

DOI: https://doi.org/10.1021/acs.analchem.7b03197

IF: 7.4

2017-01-01

Analytical Chemistry

Abstract:In this work, a new strategy for electrochemical analysis of enzyme has been proposed based on a self-assembled lipid bilayer on an electrode surface mediated by hydrazone chemistry. Taking aldolase as an example, the enzyme can catalyze the formation of products containing carbonyl groups. These groups can react with hydrazine groups of the functional lipid derivative, resulting in the self-assembly of a lipid bilayer on a guanidinium modified electrode surface. The lipid bilayer will then prevent the movement of hydrophilic electrochemical probes. Consequently, the catalytic reaction of the enzyme may result in the change of the obtained electrochemical peak current. Experimental results reveal that aldolase activity can be analyzed over a widely linear detection range from 5 mU/L to 100 U/L with a low detection limit of 1 mU/L. Meanwhile, the method can exhibit good precision and reproducibility and it can be applied for real sample analysis. What is more, because the lipid bilayer is the universal basis for cell-membrane structure, while hydrazone chemistry is popular in nature, this work may also provide a new insight for the development of electrochemical analysis and electrochemical biosensors.
Highly sensitive electrogenerated chemiluminescence biosensor in profiling protein kinase activity and inhibition using gold nanoparticle as signal transduction probes.

Shoujiang Xu,Yang Liu,Taihong Wang,Jinghong Li

DOI: https://doi.org/10.1021/ac102296g

IF: 7.4

2010-01-01

Analytical Chemistry

Abstract:A novel electrogenerated chemiluminescence (ECL) biosensor using gold nanoparticles as signal transduction probes was described for the detection of kinase activity. The gold nanoparticles were specifically conjugated to the thiophosphate group after the phosphorylation process in the presence of adenosine 59-[c-thio] triphosphate (ATP-s) cosubstrate. Due to its good conductivity, large surface area, and excellent electroactivity to luminol oxidization, the gold nanoparticles extremely amplified the ECL signal of luminol, offering a highly sensitive ECL biosensor for kinase activity detection. Protein kinase A (PKA), an important enzyme in regulation of glycogen, sugar, and lipid metabolism in the human body, was used as a model to confirm the proof-of-concept strategy. The as-proposed biosensor presented high sensitivity, low detection limit of 0.07 U mL(-1), wide linear range (from 0.07 to 32 U mL(-1)), and excellent stability. Moreover, this biosensor can also be used for quantitative analysis of kinase inhibition. On the basis of the inhibitor concentration dependent ECL signal, the half-maximal inhibition value IC50 of ellagic acid, a PICA inhibitor, was estimated, which was in agreement with those characterized with the conventional kinase assay. While nearly no ECL signal change can be observed in the presence of Tyrphostin AG1478, a tyrosine kinase inhibitor, but not PICA inhibitor, shows its excellent performance in kinase inhibitor screening. The simple and sensitive biosensor is promising in developing a high-through assay of in vitro kinase activity and inhibitor screening for clinic diagnostic and drug development.
Embedding Capture-Magneto-Catalytic Activity into a Nanocatalyst for the Determination of Lipid Kinase.

Tao Gao,Chaoli Mu,Hai Shi,Liu Shi,Xiaoxia Mao,Genxi Li

DOI: https://doi.org/10.1021/acsami.7b10857

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:The use of emerging nanocatalysts to investigate the activity of biocatalysts (protein enzymes, catalytic RNAs, etc.) is increasingly receiving attention from material, analytic, and biomedical scientists. Here, we have first fabricated a three-in-one nanocatalyst, the nitrilotriacetic acid (NTA)-modified magnetite nanoparticle (NTA-MNP), to develop an integrated magneto-colorimetric (MagColor) assay for lipid kinase activity so as to solve the inherent problems in a lipid kinase assay. On the basis of three integrated functions of the NTA-MNPs (capture, magnetic separation, and peroxidase activity), the catalytic activity of lipid kinase is directly converted to colorimetric signals. Therefore, the assay procedure is significantly simplified such that in one step the visual detection of lipid kinase activity is possible. Moreover, the whole system responds sensitively in the case that NTA-MNPs recognize a few numbers of the reaction sites, which efficiently initiates the chromogenic reaction of a large amount of chromogens; thus, the detection limit decreases to 6.5 ± 5.8 fM, about three orders of magnitude lower as compared to that of enzyme-linked immune-sorbent assay. So, by embedding desired functions into nanocatalysts, the assay for biocatalysts becomes easy, which may promisingly provide useful tools for biomedical and clinical research in the future.
Electrochemical Impedance Spectroscopy for Real-Time Detection of Lipid Membrane Damage Based on a Porous Self-Assembly Monolayer Support

Meng Zhang,Qingyu Zhai,Liping Wan,Li Chen,Yu Peng,Chunyan Deng,Juan Xiang,Jiawei Yan

DOI: https://doi.org/10.1021/acs.analchem.8b00884

2018-06-19

Abstract:Layer-by-layer dissolution and permeable pore formation are two typical membrane damage pathways, which induce membrane function disorder and result in serious disease, such as Alzheimer's disease, Keshan disease, Sickle-cell disease, and so on. To effectively distinguish and sensitively monitor these two typical membrane damage pathways, a facile electrochemical impedance strategy was developed on a porous self-assembly monolayer (pSAM) supported bilayer lipid membrane (BLM). The pSAM was prepared by selectively electrochemical reductive desorption of the mercaptopropionic acid in a mixed mercaptopropionic acid/11-mercaptoundecanoic acid self-assembled monolayer, which created plenty of nanopores with tens of nanometers in diameter and several nanometers in height (defined as inner-pores). The ultralow aspect ratio of the inner-pores was advantageous to the mass transfer of electrochemical probe [Fe(CN)6]3-/4-, simplifying the equivalent electric circuit for electrochemical impedance spectroscopy analysis at the electrode/membrane interface. [Fe(CN)6]3-/4- transferring from the bulk solution into the inner-pore induce significant changes of the interfacial impedance properties, improving the detection sensitivity. Based on these, the different membrane damage pathways were effectively distinguished and sensitively monitored with the normalized resistance-capacitance changes of inner-pore-related parameters including the electrolyte resistance within the pore length ( Rpore) and the metal/inner-pore interfacial capacitance ( Cpore) and the charge-transfer resistance ( Rct-in) at the metal/inner-pore interface.
A Lipase-Based Electrochemical Biosensor for Target DNA

Yangyang Chen,Lin Xiao,Ying Liu,Xiaoxi Li,Juan Zhang,Yongqian Shu

DOI: https://doi.org/10.1007/s00604-014-1162-4

IF: 5.7

2014-01-01

Microchimica Acta

Abstract:A lipase-based electrochemical biosensor has been fabricated for the quantitative determination of target DNA. It is based on a stem-loop nucleic acid probe labeled with ferrocene containing a butanoate ester that is hydrolyzed by lipase. The other end of the probe DNA is linked, via carboxy groups, to magnetic nanoparticles. The binding of target DNA transforms the hairpin structure of the probe DNA and causes the exposure of ester bonds. This results in the release of electro-active ferrocene after hydrolysis of the ester bonds, and in an observable electrochemical response. The quantity of target DNA in the concentration range between 1 × 10−12 mol·L−1 and 1 × 10−8 mol·L−1 can be determined by measuring the electrochemical current. The method can detect target DNA with rapid response (30 min) and low interference.
Reporter-encapsulated liposomes on graphene field effect transistors for signal enhanced detection of physiological enzymes.

Hu Chen,Seng Koon Lim,Peng Chen,Jingfeng Huang,Yi Wang,Alagappan Palaniappan,Mark Platt,Bo Liedberg,Alfred Iing Yoong Tok

DOI: https://doi.org/10.1039/c4cp04644g

IF: 3.3

2015-01-01

Physical Chemistry Chemical Physics

Abstract:A novel approach for enzymatic assay using reporter-encapsulated liposomes on graphene field effect transistors (FET) is proposed. This approach involves real time monitoring of drain current (I-d) of reduced graphene oxide (rGO) upon rupture of reporter-encapsulated 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC) liposomes triggered by enzymes. For validation of the proposed approach, 2,4,6-trinitrophenol (TNP) is used as the reporter for specific detection of phospholipase A(2) (PLA(2)), a key enzyme in various membrane related physiological processes. Experimental results revealed that Id increased with PLA2 concentration, which is attributed to the interaction between released TNP and rGO. The limit of detection (LOD) achieved by the proposed approach was 80 pM, which is superior to most assays reported previously and much lower than the cut-off level of circulating secretory PLA2 (2.07 nM). Besides the high accuracy of the electronic detection methodology, the signal enhancement effect realized by the excess concentration of TNP (approximately 1 mM) in liposomes is believed to be the main reason for the significantly enhanced sensitivity of the proposed assay, indicating great potential for further improvement in the sensitivity by increasing the concentration of TNP. In addition, the proposed approach is rapid (incubation time <= 10 min) and label-free, thus showing great potential for practical applications in the future.
A label-free and modification-free ratiometric electrochemical strategy for enhanced natural enzyme detection using a bare electrode and nanozymes system

Honghong Rao,Jianying Li,Mingyue Luo,Kehui Zhang,Hao Gou,Haixia Liu,Zhonghua Xue

DOI: https://doi.org/10.1007/s00216-022-03932-9

2022-02-01

Analytical and Bioanalytical Chemistry

Abstract:Ratiometric electrochemical assays have been demonstrated to be more sensitive and selective in various sensing events, mainly due to their affordable built-in correction and good self-reference capability. But it is known that complicated modification and labeling operations usually are necessary for the construction of ratiometric electrochemical assays, therefore is a hot and important issue needing consideration carefully. We herein report a new yet simple bare electrode-based ratiometric electrochemical bioassay to achieve sensitive and selective analysis of alkaline phosphatase (ALP), using a liquid phase system that contains CoOOH nanozymes and commercially available indicator substrate. This proposed bioassay works based on the ratiometric change of dual electrochemical signals, arising from an exclusive target ALP-triggered hydrolysis of electrochemical substrate p-nitrophenyl phosphate (PNPP). In this design, the two hydrolyzed products of electrochemically active p-nitrophenol (PNP) and electrochemically inactive phosphate anion (PO43−) are responsible together for the ratiometric electrochemical analysis of ALP. PNP exhibits a straightforward current response toward ALP content; however, PO43− cannot show a direct electrochemical signal thus is rationally designed to offer an alternative response by linking it with the specific CoOOH nanozyme-catalyzed reaction of 3,3′,5,5′-tetramethylbenzidine (TMB) and H2O2, in which the nanozyme-catalyzed product oxTMB shows a direct reduction current at the GCE, and significantly decreases with increasing PO43− species due to the good inhibition of PO43− toward CoOOH nanozyme activity. As a result, a ratiometric electrochemical strategy for ALP analysis with a low limit of detection of 0.366 U/L (S/N = 3) was successfully achieved by integrating the above direct and indirect dual electrochemical responses. This developed bioassay can allow the quantitative diagnosis of ALP activity especially with a label-free and modification-free merit, therefore paving the way for simple, convenient, and portable electroanalytical tools in biosensing design and application.Graphical abstract

chemistry, analytical,biochemical research methods
Cell Membrane-Anchored Biosensors for Real-Time Monitoring of the Cellular Microenvironment

Liping Qiu,Tao Zhang,Jianhui Jiang,Cuichen Wu,Guizhi Zhu,Mingxu You,Xigao Chen,Liqin Zhang,Cheng Cui,Ruqin Yu,Weihong Tan

DOI: https://doi.org/10.1021/ja5047389

IF: 15

2014-09-16

Journal of the American Chemical Society

Abstract:Cell membrane-anchored biochemical sensors that allow real-time monitoring of the interactions of cells with their microenvironment would be powerful tools for studying the mechanisms underlying various biological processes, such as cell metabolism and signaling. Despite the significance of these techniques, unfortunately, their development has lagged far behind due to the lack of a desirable membrane engineering method. Here, we propose a simple, efficient, biocompatible, and universal strategy for one-step self-construction of cell-surface sensors using diacyllipid-DNA conjugates as the building and sensing elements. The sensors exploit the high membrane-insertion capacity of a diacyllipid tail and good sensing performance of the DNA probes. Based on this strategy, we have engineered specific DNAzymes on the cell membrane for metal ion assay in the extracellular microspace. The immobilized DNAzyme showed excellent performance for reporting and semiquantifying both exogenous and cell-extruded target metal ions in real time. This membrane-anchored sensor could also be used for multiple target detection by having different DNA probes inserted, providing potentially useful tools for versatile applications in cell biology, biomedical research, drug discovery, and tissue engineering.

chemistry, multidisciplinary
Real-Time and Spatial Electroanalysis of Biomolecules in One Living Cell Using Liquid-Phase Modified Nanopipette

Kang Liu,Rujia Liu,Dengchao Wang,Rongrong Pan,Hong-Yuan Chen,Dechen Jiang

DOI: https://doi.org/10.31635/ccschem.023.202202397

2023-01-01

CCS Chemistry

Abstract:The well-developed solid-phase modified strategy at the electrode has enabled the preparation of biosensors for the detection of multiple analytes, even in single living cells. However, limited assay elements can be modified at the solid surface, restricting the types of molecules that can be analyzed and the sensitivity of detection. Here, a novel liquid-phase modified strategy at the tip of a nanopipette is designed to realize real-time and local analysis of biomolecules inside the cell that are barely detectable using solid-phase modified nanoelectrodes. This design utilizes the nanotip structure at a platinized carbon open nanopipette to stably retain a nanodroplet that contains the required reagents with high reactivity for the assay of the target analyte. The generated hydrogen peroxide is electrochemically quantified at the Pt layer to carry out the real-time measurement in a living cell with a spatial resolution of 70 nm. Taking advantage of highly spatial and real-time detection, uneven distribution of sphingomyelinase (SMase) in the living CT26 cell is unprecedentedly shown to exhibit the significance in the establishment of liquid-phase modified nanopipette. This new modification strategy opens up a new direction for sensor design and consequently advances the development of biosensors in the chemical and biological research. [GRAPHICS] .
An Integral Recognition and Signaling for Electrochemical Assay of Protein Kinase Activity and Inhibitor by Reduced Graphene Oxide-Polydopamine-Silver Nanoparticle-Ti4+ Nanocomposite

Jialong Wang,Xueqian Liu,Chao Wang,Dengren Liu,Fang Li,Li Wang,Shufeng Liu

DOI: https://doi.org/10.3389/fbioe.2020.603083

IF: 5.7

2020-11-13

Frontiers in Bioengineering and Biotechnology

Abstract:A novel electrochemical biosensing method for protein kinase (PKA) activity was demonstrated by using a reduced graphene oxide-polydopamine-silver nanoparticle-Ti4+ (rGO-PDA-AgNPs-Ti4+) nanocomposite. The obtained nanocomposite possessed an integral capability for phosphopeptide recognition and signal readout. The polydopamine modified reduced graphene oxide (rGO-PDA) was firstly prepared based on a self-polymerization method of dopamine. The silver ions were adsorbed onto polydopamine (PDA) layer and directly reduced into silver nanoparticles (AgNPs), which was used for electrochemical signal reporting. Then, the Ti4+ cations were attached onto the PDA layer for phosphopeptide recognition according to the strong coordination ability of PDA with Ti4+ and phosphate group. The prepared rGO-PDA-AgNPs-Ti4+ nanocomposites were characterized with different methods. The developed rGO-PDA-AgNPs-Ti4+ nanocomposites were then employed for electrochemical analysis of PKA-catalyzed kemptide phosphorylation. The sensitive detection toward PKA activity was realized with an experimental detection limit of about 0.01 U/mL. It may be also extended for the inhibitor evaluation. Thus, it provided a facile and sensitive means for electrochemical analysis of PKA activity and inhibitor screening.

multidisciplinary sciences
Single molecule Lipid Biosensors Mitigate Inhibition of Endogenous Effector Proteins

Victoria Holmes,Morgan M. C. Ricci,Claire C. Weckerly,Michael Worcester,Gerald R. V. Hammond

DOI: https://doi.org/10.1101/2024.09.11.612480

2024-09-16

Abstract:Genetically encoded lipid biosensors are essential cell biological tools. They are the only technique that provide real time, spatially resolved kinetic data for lipid dynamics in living cells. Despite clear strengths, these tools also carry significant drawbacks; most notably, lipid molecules bound to biosensors cannot engage with their effectors, causing inhibition. Here, we show that although PI 3-kinase (PI3K)-mediated activation of Akt is not significantly reduced in a cell population transfected with a PH-Akt1 PIP /PI(3,4)P biosensor, single cells expressing the PH-Akt at visible levels (used for live-cell imaging) have no activated Akt at all. Tagging endogenous AKT1 with neonGreen at its genomic locus reveals its EGF-mediated translocation to the plasma membrane, accumulating at densities of ~0.3 molecules/ m . Co-transfection with the PH-Akt biosensor or other PIP biosensors completely blocks this translocation, despite robust recruitment of the biosensors. A partial inhibition is even observed with PI(3,4)P -selective biosensor. However, we found that expressing lipid biosensors at low levels, comparable with those of endogenous AKT, produced no such inhibition. Helpfully, these single-molecule biosensors revealed improved dynamic range and kinetic fidelity compared with over-expressed biosensor. This approach represents a less invasive way to probe spatiotemporal dynamics of the PI3K pathway in living cells.

Cell Biology
Electrochemical Biosensor for the detection of low density lipoprotein based on gold nanoparticles mediated bi-enzymes catalytic silver deposition reaction

Ruiyu Luo,Jinghua Li,Guoying Huang,Guiyin Li,Shibin Guo,Yulin Yuan

DOI: https://doi.org/10.1016/j.microc.2024.109927

IF: 5.304

2024-01-22

Microchemical Journal

Abstract:Low-density lipoprotein (LDL) levels are utilized in the assessment of an individual's cardiovascular disease risk and serve as a valuable tool in the determination of appropriate treatment plans. This study aimed to design and evaluate a novel electrochemical biosensor using a modified glassy carbon electrode (GCE) coated with gold nanoparticles (Au-NPs) and poly-o-aminobenzenethiol (poly(oATP)) films. The novel biosensor was designed to effectively detect and measure LDL levels in biological samples. In this study, antibody apolipoprotein B (AAB) was employed as a biorecognition element to capture LDL and was subsequently immobilized on the surface of the GCE/poly(oATP)/AuNPs. Cholesterol esterase and cholesterol oxidase bi-enzymes were applied to the GCE/poly(oATP)/AuNPs/AAB/LDL surface, catalyzing the oxidation of LDL and producing hydrogen peroxide (H 2 O 2 ). The generated H 2 O 2 , in turn, facilitated the reduction of silver (Ag) ions in the solution to metallic Ag, depositing it on the GCE/poly(oATP)/AuNPs surface. The quantification of the deposited Ag, originating from the LDL, was achieved using linear sweep voltammetry. Further, we found a linear relationship between the oxidation current of the deposited Ag and the concentration of LDL, spanning from 10 to 1,000 ng/mL, with an optimal correlation coefficient of 0.9982. The limit of detection for the assay was established at 3.25 ng/mL, determined by a signal-to-noise ratio of 3. In addition, the ultrasensitive LDL biosensor demonstrated high specificity, acceptable reproducibility, and prolonged stability. These findings highlighted the successful application of this novel method for detecting LDL levels in human serum samples.

chemistry, analytical
Reduced Graphene Oxide-Zirconium Dioxide-Thionine Nanocomposite Integrating Recognition, Amplification, and Signaling for an Electrochemical Assay of Protein Kinase Activity and Inhibitor Screening.

Zhiqiang Chen,Ying Liu,Lijie Hao,Zhencai Zhu,Fang Li,Shufeng Liu

DOI: https://doi.org/10.1021/acsabm.8b00451

2018-01-01

ACS Applied Bio Materials

Abstract:Protein kinase activity analysis is essential and important for elucidation of many fundamental biological processes, disease diagnosis, and drug discovery. Herein, a novel electrochemical biosensing method for protein kinase (PKA) activity was demonstrated by the use of a reduced graphene oxide-zirconium dioxide-thionine (rGO-ZrO2-Thi) nanocomposite, which interestingly served as an integral phosphopeptide-recognizing, signal amplifying and reporting platform. The ZrO2 nanoparticle-decorated reduced graphene oxide (rGO-ZrO2) was first prepared by a hydrothermal reaction route, and then the thionine was conjugated onto the rGO surface via π-π stacking as an excellent electrochemical probe. The prepared rGO-ZrO2-Thi nanocomposites were well-characterized by various techniques. With the full advantage of specific recognition of ZrO2 nanoparticles for the phosphate group, signal amplification, and transduction of abundant thionines onto the rGO surface, and excellent conductivity of rGO, the rGO-ZrO2-Thi nanocomposite endowed a label-free and one-step electrochemical analysis of kemptide phosphorylation catalyzed by PKA. The detection limit for PKA activity was experimentally achieved as 0.005 U/mL, which was evidently lower than most of the reported methods. The proposed sensing strategy could be also applied for an efficient inhibitor evaluation. Therefore, it offered an excellent pathway for a generic and sensitive electrochemical assay of PKA activity and inhibitor.
Separation of phospholipids in microfluidic chip device: application to high-throughput screening assays for lipid-modifying enzymes

Sansan Lin,Anthony S Fischl,Xiahui Bi,Wally Parce

DOI: https://doi.org/10.1016/s0003-2697(02)00616-4

IF: 2.9

2003-03-01

Analytical Biochemistry

Abstract:Phospholipid molecules such as ceramide and phosphoinositides play crucial roles in signal transduction pathways. Lipid-modifying enzymes including sphingomyelinase and phosphoinositide kinases regulate the generation and degradation of these lipid-signaling molecules and are important therapeutic targets in drug discovery. We now report a sensitive and convenient method to separate these lipids using microfluidic chip-based technology. The method takes advantage of the high-separation power of the microchips that separate lipids based on micellar electrokinetic capillary chromatography (MEKC) and the high sensitivity of fluorescence detection. We further exploited the method to develop a homogenous assay to monitor activities of lipid-modifying enzymes. The assay format consists of two steps: an on-plate enzymatic reaction using fluorescently labeled substrates followed by an on-chip MEKC separation of the reaction products from the substrates. The utility of the assay format for high-throughput screening (HTS) is demonstrated using phospholipase A(2) on the Caliper 250 HTS system: throughput of 80min per 384-well plate can be achieved with unattended running time of 5.4h. This enabling technology for assaying lipid-modifying enzymes is ideal for HTS because it avoids the use of radioactive substrates and complicated separation/washing steps and detects both substrate and product simultaneously.

biochemistry & molecular biology,biochemical research methods,chemistry, analytical
Sensitive label-free monitoring of protein kinase activity and inhibition using ferric ions coordinated to phosphorylated sites as electrocatalysts.

Min Wang,Gui-Xia Wang,Fang-Nan Xiao,Yun Zhao,Kang Wang,Xing-Hua Xia

DOI: https://doi.org/10.1039/c3cc43290d

IF: 4.9

2013-01-01

Chemical Communications

Abstract:Ferric ions show high affinity to the kinase-generated phosphorylated sites of peptides. Thus, the high electrocatalytic activity of the coordinated ferric ions toward the reduction of hydrogen peroxide can be used for sensitive label-free monitoring of protein kinase activity and inhibition.

Electrochemical assay of lipid kinase activity facilitated by liposomes

Bioelectronic modulation of single-wavelength localized surface plasmon resonance (LSPR) for the detection of electroactive biomolecules

Enediol-Ligands-Encapsulated Liposomes Enables Sensitive Immunoassay: A Proof-of-Concept for General Liposomes-Based Photoelectrochemical Bioanalysis.

Electrochemical detection of kinase by converting homogeneous analysis into heterogeneous assay through avidin-biotin interaction

Multiple Signal Amplification Electrogenerated Chemiluminescence Biosensors for Sensitive Protein Kinase Activity Analysis and Inhibition.

A simple strategy to monitor lipase activity using liquid crystal-based sensors

Electrochemical analysis of enzyme based on the self-assembly of lipid bilayer on an electrode surface mediated by hydrazone chemistry.

Highly sensitive electrogenerated chemiluminescence biosensor in profiling protein kinase activity and inhibition using gold nanoparticle as signal transduction probes.

Embedding Capture-Magneto-Catalytic Activity into a Nanocatalyst for the Determination of Lipid Kinase.

Electrochemical Impedance Spectroscopy for Real-Time Detection of Lipid Membrane Damage Based on a Porous Self-Assembly Monolayer Support

A Lipase-Based Electrochemical Biosensor for Target DNA

Reporter-encapsulated liposomes on graphene field effect transistors for signal enhanced detection of physiological enzymes.

A label-free and modification-free ratiometric electrochemical strategy for enhanced natural enzyme detection using a bare electrode and nanozymes system

Cell Membrane-Anchored Biosensors for Real-Time Monitoring of the Cellular Microenvironment

Real-Time and Spatial Electroanalysis of Biomolecules in One Living Cell Using Liquid-Phase Modified Nanopipette

An Integral Recognition and Signaling for Electrochemical Assay of Protein Kinase Activity and Inhibitor by Reduced Graphene Oxide-Polydopamine-Silver Nanoparticle-Ti4+ Nanocomposite

Single molecule Lipid Biosensors Mitigate Inhibition of Endogenous Effector Proteins

Electrochemical Biosensor for the detection of low density lipoprotein based on gold nanoparticles mediated bi-enzymes catalytic silver deposition reaction

Reduced Graphene Oxide-Zirconium Dioxide-Thionine Nanocomposite Integrating Recognition, Amplification, and Signaling for an Electrochemical Assay of Protein Kinase Activity and Inhibitor Screening.

Separation of phospholipids in microfluidic chip device: application to high-throughput screening assays for lipid-modifying enzymes

Sensitive label-free monitoring of protein kinase activity and inhibition using ferric ions coordinated to phosphorylated sites as electrocatalysts.