Abstract:The deformation behavior of a radially forged 2A50 aluminum alloy was investigated by thermal compression test at high-temperature solid (300–500 °C) and semi-solid (565–585 °C) states with strain rates of 0.01–0.5s–1. A strain-compensated Arrhenius constitutive equation was established to describe the relationship between flow stress and compression parameters. The inhomogeneous deformation and microstructure evolution of the specimen were explored. Results reveal that the strain-compensated Arrhenius model can accurately predict experimental flow stress in both two temperature states. In the high-temperature solid state, the equilibrium between the softening effect (dynamic recovery and dynamic recrystallization) and work hardening leads to a steady stage of the flow curves after peak. In the semi-solid temperature, the softening mechanisms mainly include the high level of dynamic recrystallization (DRX), lubrication of liquid phases, and partial collapse of solid-phase skeleton, contributing to a declining stage of flow stress after peak. Strain and temperature profoundly influence DRX. At high-temperature solid state, coarse and elongated grains predominate in the regions with small strain, whereas DRX and numerous subgrains massively occur in the regions with large strain. The entire sample compressed in semi-solid temperature is subjected to DRX, attributed to the elevated temperature compared to the high-temperature solid state. Fine DRX grains are concentrated at the center of the large deformation zone (with large strain) due to the frequent DRX. Elevating semi-solid temperature leads to the formation of large equiaxed grains. DRX facilitates the weakening of deformed textures, demonstrated by the presence of deformed textures (<111> and <100>//X0 fiber textures, <111>//Z0 fiber texture, and {110}<111> texture) in the sample at high-temperature solid state, contrasted with the absence of pronounced preferred orientation in semi-solid compressed sample.

Microstructural Evolution of Semisolid 6063 Aluminum Alloy Prepared by Recrystallization and Partial Melting Process

Microstructure of Semi-Solid 6063 Alloy Fabricated by Radial Forging Combined with Unidirectional Compression Recrystallization and Partial Melting Process

Grain Refinement of Aluminum Alloy Bar by A Modified Rap Process for Semi-Solid Forming

Unexpected Dynamic Recrystallization Behavior of Ti-7Cu Alloy in Semi-Solid State

Semi-Solid Billets Prepared by Radial Forging Strain-Induced Melt Activation

Semi-solid Billet Prepared by Radial Forging Combined with Unidirectional Compression Recrystallization and Partial Melting

Microstructural Coarsening of 6061 Aluminum Alloy Semi-Solid Billets Prepared Via Recrystallization and Partial Melting

The Microstructural Evolution of a Cold Rolled AlSi9Mg Aluminum Alloy after Semi-Solid Isothermal Treatment Process

Effect of cross-sectional reduction ratio on microstructure evolution of semi-solid 7075 aluminum alloy prepared by RFSIMA process

Application of Radial Forging and Remelting Treatment to Prepare Semi-Solid Billet of AlMg0.7Si Alloy

Microstructural Evolution of 7050 Aluminum Alloy Semisolid Billets Fabricated by RAP Process

Microstructural Evolution of ZL104 Aluminum Alloy Semi-Solid Billet Fabricated by RAP Process

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Comparison of Microstructural Evolution of 7075 Aluminum Alloy Fabricated by SIMA and RAP

Effects of Temperature and Time on Microstructural Evolution of Semisolid 5A06 Aluminum Alloy: Preparation of Semisolid Billets in Ellipsoid Solid Phase

Deformation Behaviour and Microstructures of Semi-Solid A356.2 Alloy Prepared by Radial Forging Process During High Solid Fraction Compression

Recrystallization process of hot-extruded 6A02 aluminum alloy in solid and semi-solid temperature ranges

Effect of Heating Process on Semi-solid Microstructure of Cold Rolled 6061 Aluminum Alloy

Deformation Behavior and Microstructure Characterization of the Radially Forged 2A50 Aluminum Alloy at High-Temperature Solid and Semi-Solid States

Microstructure Evolution of 7005 Alloy Semisolid Billets Fabricated by Large Deformation-Induced Isothermal Spheroidization

Preparation of Large-Diameter Semi-Solid 7075 Aluminum Alloy Billets