Abstract:A critical challenge in the commercialization of spinel lithium manganate materials is the bulk structure damage and capacity degradation due to manganese dissolution during battery operation. Hence, Li3PO4 with good ionic conductivity was homogeneously deposited on the surface of spinel lithium manganate by the sol-gel method, aiming to improve the stability and cycling of the spinel structure by an epitaxial layer. The structural and electrochemical characterizations reveal that the presence of the Li3PO4 epitaxial coating prevents the direct contact of the cathode surface and electrolyte, thus enhancing the stability of the structure and reducing the extent of manganese dissolution. Further studies have shown that the contribution of the Li3PO4 layer promotes the diffusion coefficient of lithium ions, which increases from 7.89 x 10-12 to 4.43 x 10-11 cm2 s-1. Meanwhile, the Li3PO4 coating regulates the concentration of oxygen vacancies on the surface of the spinel, effectively reducing the transfer resistance and increasing the electronic conductivity to 3.50 x 10-5 cm-1. Specifically, the discharge specific capacity of the 1.0 wt % Li3PO4- modified electrode is still 115.4 mAh g-1 after 300 cycles, with the capacity retention increased to 90.8%. Even at a high rate of 10C, it still demonstrates excellent rate capability, with the discharge specific capacity more elevated than that of the unmodified material at about 40 mAh g-1. This strategy can simultaneously solve the interfacial instability and bulk structure degradation, thus improving the electrochemical performance of lithium manganate materials.

TiO2-Modified Spinel Lithium Manganate for Suppressing Mn Ion Dissolution in Lithium Ion Batteries

Effectively Suppressing Dissolution of Manganese from LiMn2O4 Spinel Via a Novel Nanoscale Surface-Doping Approach

Enhanced High-Potential and Elevated-Temperature Cycling Stability of Limn2o4 Cathode by Tio2 Modification for Li-Ion Battery

Surface Magnesium Substitution at Spinel Lithium Manganate 8a Tetrahedral Sites for Suppressed Manganese Dissolution and Enhanced Cycle Stability

Effectively suppressing dissolution of manganese from spinel lithium manganate via a nanoscale surface-doping approach

Mechanism of Capacity Fading Caused by Mn (II) Deposition on Anodes for Spinel Lithium Manganese Oxide Cell

Surface Modification Mechanism of Spinel Structure LiM_xMn_(2-x)O_4 As Cathode Materials for Lithium Ion Batteries

Lithium-Ion Conductivity Epitaxial Layer Contributing to the Structure and Cycling Stability of LiMn2O4 Cathodes

Capacity fading of high specific capacity spinel LixMn2-yTiyO4 as cathode material for Li-ion batteries

Suppression of Jahn–Teller distortion of spinel LiMn2O4 cathode

Electrochemical Properties of Tetravalent Ti-doped Spinel LiMn 2 O 4

Enhancing the Electrochemical Properties of Ti-Doped LiMn 2 O 4 Spinel Cathode Materials Using a One-Step Hydrothermal Method

Research Development on Spinel Lithium Manganese Oxides Cathode Materials for Lithium-Ion Batteries

Strengthening Reversibility at High Rate of Spinel LiMn 2 O 4 by Aluminum and Copper Co-doping for Lithium Ion Battery

Nanoscale TiO2 Membrane Coating Spinel LiNi0.5Mn1.5O4 Cathode Material for Advanced Lithium-Ion Batteries

Strengthening Reversibility at High Rate of Spinel LiMn2O4 by Aluminum and Copper Co-doping for Lithium Ion Battery

Bulk and surface reconstructed Li-rich Mn-based cathode material for lithium ion batteries with eliminating irreversible capacity loss

Preparation and Characterization of M(II) and M(IV) Iso-Molar Co-Doped Li Mn_(1.9)Mg_(0.05)Ti_(0.05)O_4 Cathode Materials for Lithium-Ion Batteries

Preparation and Characterization of M(II) and M(IV) Iso-Molar Co-Doped LiMn1.9Mg0.05Ti0.05O4 Cathode Materials for Lithium-Ion Batteries

Correlation Between Manganese Dissolution and Dynamic Phase Stability in Spinel-Based Lithium-Ion Battery

Structure and Electrochemical Performance of Modificated LiMn<sub>2</sub>O<sub>4</sub> by S-Co Codoping and Nano SiO<sub>2</sub> Surface Coating