Abstract:As one of the most promising heat-resistant magnesium alloys, Mg-Gd series alloy has a wide application prospect in the industrial fields of aerospace, cars, and rail transit. There have been extensive researches on the performance improvement of Mg-Gd series alloys. As known, dendrites are the common solidification microstructures of castings of magnesium alloys, and solidification conditions have a significant effect on dendrite morphologies and growth orientation, which could strongly affect the mechanical properties of castings, thus it is critical to study the grain growth regularity for predicting the performance of magnesium castings. However, there are few studies on numerical simulation of dendrite growth process and growth orientation of magnesium alloys. Solidification behavior of magnesium alloys can be scientifically studied via directional solidification technology, and cellular automaton finite element (CAFE) method should be effective to simulate the dendrite growth process of magnesium alloys. In present work, microstructures and growth orientation of directionally solidified Mg- 14.61Gd alloy under the temperature gradient G=30 K/mm and the withdrawal rate v=10 similar to 200 mu m/s were investigated by EBSD measurement method and CAFE numerical simulation method. It was found that alpha-Mg primary phase presented unidirectional dendritic morphologies on longitudinal cross-section. The growth interface appearance of alpha-Mg changed from the protruding forward growth to the flat growth gradually and the dendritic arm spacing decreased gradually with the increasing v. when v increased from 10 mu m/s to 100 mu m/s, the main growth orientation of alpha-Mg changed from <11<(2)over bar>0> and <10<(1)over bar>0> to <11<(2)over bar>0>, and the deviation angle (theta) from solidification heat flow direction reduced from 11.0 degrees to 5.7 degrees, the reason for this lied mainly in the change of the heat flux. Further increasing v up to 200 mu m/s, the main growth direction of alpha-Mg was still in <11<(2)over bar>0>, but the value of theta increased to 10.6 degrees, and the anisotropy of the crystal was the dominant factor then. It was proved that the CAFE numerical simulation model could predict the grain structure and growth orientation reasonably for Mg alloy.

Microstructures and Microsegregation of Directionally Solidified Mg-1.5Gd Magnesium Alloy with Different Growth Rates

Microstructure and room temperature mechanical properties of directionally solidified Mg–2.35Gd magnesium alloy

Microstructure Evolution and Mechanical Properties of Directionally Solidified Mg-xGd (x=0.8, 1.5, and 2.5) Alloys

Dependence of Microstructures and Mechanical Properties on the Growth Rate and Composition in Directionally Solidified Mg-Gd Alloys

Microstructure, Microsegregation, and Mechanical Properties of Directional Solidified Mg–3.0Nd–1.5Gd Alloy

Study on Directional Solidification Microstructures of Mg-Zn-Gd Ternary Magnesium Alloy

Microstructures and Growth Orientation of Directionally Solidification Mg-14.61Gd Alloy

Effects of the Growth Rate on Microstructures and Room Temperature Mechanical Properties of Directionally Solidified Mg-5.2Zn Alloy

Microstructural evolution, phase constitution and mechanical properties of directionally solidified Mg-5.5Zn-xGd (x = 0.8, 2.0, and 4.0) alloys

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Directional Solidification and Microsegregation in a Magnesium-Aluminum-Calcium Alloy

Effects of Composition and Growth Rate on the Microstructure Transformation of Β-Rods/lamellae/α-rods in Directionally Solidified Mg-Li Alloy

Effect of dynamic recrystallization, LPSO phase, and grain boundary segregation on heterogeneous bimodal microstructure in Mg-9.8Gd-3.5Y-2.0Zn-0.4Zr alloy

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Evolution of the Microstructure and Microsegregation in Subrapidly Solidified Mg–6Al–4Zn–1.2Sn Magnesium Alloy

Microstructure Evolution During Reheating of Extruded Mg-Gd-Y-Zr Alloy into Semisolid State

Microstructure Evolution, Mechanical Properties and Diffusion Behaviour of Mg-6Zn-2Gd-0.5Zr Alloy During Homogenization

Phase-Field Simulation on the Influence of Cooling Rate on the Solidification Microstructure of Mg-Gd-Y Ternary Magnesium Alloy

Effect of Growth Rate on Microstructure Evolution in Directionally Solidified Ti–47Al Alloy

Microstructural evolution of Mg-10Gd-3Y-1Zn-0.4Zr (wt%) alloy prepared by strain-induced melt activation process

Mechanical Behaviors of Extruded Mg Alloys with High Gd and Nd Content